Watlow EZ-ZONE RMC Manual de usuario descargar pdf (Pagina 89)

Watlow EZ-ZONE

RMC Module • 86 • Chapter 4 Setup Page

RMC Module • Setup Page

Dis-

play

Parameter Name

Description

Range Default

Modbus

Relative

Address

CIP

Class

Instance

Attribute

hex (dec)

Probus

Index

Parameter

Data

Type

& Read/

Write

[`A;hi]

[ A.hi]

Alarm (1 to 8)

High Set Point **

If Alarm Type (Setup

Page, Alarm Menu) is

set to:

process - set the pro-

cess value that will

trigger a high alarm.

deviation - set the

span of units from the

closed loop set point

that will trigger a low

alarm. A negative set

point represents a

value below closed loop

set point. A positive

set point represents a

value above closed loop

set point.

-1,999.000 to 9,999.000°F or

units

-1,128.000 to 5,537.000°C

300.0°F

or units

150.0°C

1740

[offset

60]

0x6D

(109)

1 to 8

19 9001 float

RWES

[`A;LA]

[ A.LA]

Alarm (1 to 8)

Latching

Turn alarm latching on

or off. A latched alarm

has to be turned off by

the user.

[nLAt] Non-Latching (60)

[`LAt] Latching (49)

Non-

Latching

1752

[offset 60]

0x6D

(109)

1 to 8

27 9007 uint

RWES

[`A;bL]

[ A.bL]

Alarm (1 to 8)

Blocking

Select when an alarm

will be blocked. After

startup and/or after the

set point changes, the

alarm will be blocked

until the process value

enters the normal range.

[`oFF] Off (62)

[`Str] Startup (88)

[StPt] Set Point (85)

[both] Both (13)

Off 1754

[offset 60]

0x6D

(109)

1 to 8

28 9008 uint

RWES

[`A;Si]

[ A.Si]

Alarm (1 to 8)

Silencing

Turn alarm silencing on

to allow the user to dis-

able this alarm.

[`oFF] Off (62)

[``on] On (63)

Off 1750

[offset 60]

0x6D

(109)

1 to 8

29 9006 uint

RWES

[A;dSP]

[A.dSP]

Alarm (1 to 8)

Display

Display an alarm mes-

sage when an alarm is

active.

[`oFF] Off (62)

[``on] On (63)

On 1770

[offset 60]

0x6D

(109)

1 to 8

0x10 (16)

30 9016 uint

RWES

[`A;dL]

[ A.dL]

Alarm (1 to 8)

Delay Time

Set the span of time

that the alarm will be

delayed after the process

value exceeds the alarm

set point.

0 to 9,999 seconds 0 1780

[offset 60]

0x6D

(109)

1 to 8

0x15 (21)

31 9021 uint

RWES

Note:

Some values will be rounded off to fit in the four-character display.

Full values can be read with other interfaces.

Note:

If there is only one instance of a menu, no submenus will appear.

** These parameters/prompts are available in these menus with firmware revisions 6.0 and

above.

R: Read

W: Write

E: EEPROM

S: User Set

1 2 ... 84 85 86 87 88 89 90 91 92 93 94 ... 235 236

Comentarios a estos manuales

Sin comentarios

Watlow EZ-ZONE RMC Manual de usuario Pagina 89

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RMC