Watlow EZ-ZONE RMC Manual de usuario Pagina 38
- Pagina / 236
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Watlow EZ-ZONE
®
RMC Module • 35 • Chapter 2 Install and Wire
Wiring a Serial EIA-485 Network
Do not route network wires with power wires. Con-
nect network wires in daisy-chain fashion when con-
necting multiple devices in a network. A termina-
tion resistor may be required. Place a 120 Ω resistor
across T+/R+ and T-/R- of the last controller on a
network. Only one protocol per port is available at a
time: either Modbus RTU or Standard Bus.
Note:
Termination resistors when used, require a termina-
tion resistor at both ends of the network.
A Network Using Watlow's Standard Bus and an RUI/Gateway
- A
+ B
com
- A
+ B
common
power
- A
+ B
common
power
power
power
EZ-ZONE PM
EZ-ZONE ST
ST_ _ - (B or F) _ M _ -_ _ _ _
98
99
CF
CD
CE
B5
D6
D5
Power
Supply
fuse
EZ-ZONE RM
98
99
S
l
o
t
C
power
CZ
CE
CX
CY
CD
CF
- A
+ B
common
98
99
CF
CD
CE
B5
D6
D5
98
99
CF
CD
CE
RUI/Gateway
EZKB-_ A _ _- _ _ _ _
A Network Using Modbus RTU
- A
+ B
com
98
99
CC
CA
CB
B5
D6
D5
power
- A
+ B
common
power
- A
+ B
common
power
power
power
power
EZ-ZONE PM
EZ-ZONE ST
ST_ _ - (B or F) _ M _ -_ _ _ _
PLC
98
99
CC
CA
CB
B5
D6
D5
Power
Supply
fuse
EZ-ZONE RM
98
99
S
l
o
t
C
power
CZ
CB
CX
CY
CA
CC
- A
+ B
common
- User’s Guide 1
- RMC (Control) Module 1
- Control Module 1
- Safety Information 2
- Warranty 2
- Technical Assistance 2
- Table of Contents 4
- Table of Contents (cont.) 5
- Chapter 1: Overview 7
- Introduction 8
- • 6 • Chapter 1 Overview 9
- Getting Started Quickly 10
- Functions 10
- Function 11
- Slot CSlot C 12
- Module Orientation 13
- Chapter 2: Install and Wire 16
- Dimensions 17
- Power Supplies 18
- Modular Backplane Connector 19
- Module Installation 19
- Removal of the Modular Back 20
- Module Removal 20
- Power and Communications 22
- RMC Module Isolation Diagram 24
- Slot A, B, D, E 25
- RMC Part # Digits 4, 6, 8, 10 26
- RMC Part # Digit 11 is C 28
- Output 2, 4, 6, 8 Switched DC 30
- Safe Operating Area 33
- A Network Using Modbus RTU 38
- Connecting the Modules 39
- [``o;u] Output Value 42
- [`Ain] Value ** 63
- [`Set] Timer Menu 64
- Offset the input reading 68
- 0x68 (104) 68
- 0x70 (112) 76
- Set an offset value for a 87
- 0x80 (128) 95
- 0x83 (131) 95
- 0x82 (130) 100
- 0x7F (127) 100
- Watlow EZ-ZONE 110
- 0x87 (135) 116
- On (63) 119
- Profiling Parameters 131
- [`Pro] Process 148
- Change this value to 152
- Chapter 7: Features 154
- Chapter 7: Features (cont.) 155
- Tuning the PID Parameters 156
- Autotuning with TRU-TUNE+ 157
- Before Tuning 157
- How to Autotune a Loop 157
- • 155 • Chapter 7 Features 158
- • 156 • Chapter 7 Features 159
- Temperature 160
- Control Methods 161
- On-Off Control 162
- Proportional (P) Control 163
- Dead Band 163
- Variable Time Base 164
- Single Set Point Ramping 164
- Cascade Control 165
- Compressor Control 165
- Differential Control 165
- Input 1 Output 1 166
- Resetting a Tripped Limit 167
- Open Loop Detection 168
- Programming the EZ Key/s 168
- Current Sensing 168
- Using Password Security 169
- • 167 • Chapter 7 Features 170
- • 168 • Chapter 7 Features 171
- Software Configuration 172
- • 170 • Chapter 7 Features 173
- • 171 • Chapter 7 Features 174
- Function Block Descriptions 175
- Analog Input Function 176
- -1,999.000 to 9,999.000 176
- Overview 177
- Control Function 179
- Counter Function 181
- Custom Function 181
- Diagnostic Function 181
- Digital Input/Output Function 182
- Global Function 182
- Math Function 187
- Switch Over 189
- Multiply 190
- Absolute Difference 191
- Range Low 193
- Profile Function 194
- Profiling 197
- Unused Step Type 197
- Time Step Type 198
- Rate Step Type 199
- Soak Step Type 200
- State Step Type 201
- Jump Step Type 203
- Wait Time 204
- Subroutine Step Type 205
- End Step Type 206
- Process Value Function 207
- Output Value 207
- Process Value 208
- Setting 212
- Timer Function 214
- One Shot 217
- Retentive 218
- Variable 219
- Chapter 8: Appendix 220
- • 221 • Chapter 8 Appendix 224
- Control Module Specifications 227
- Digital Input 228
- Dry Contact 228
- Output Hardware 229
- Output Hardware (cont.) 229
- • 228 • Chapter 8 Appendix 231
- • 229 • Chapter 8 Appendix 232
- • 230 • Chapter 8 Appendix 233
- • 231 • Chapter 8 Appendix 234
- EZ Zone Series RM 235
- How to Reach Us 236
Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RMC
Sensores Watlow EZ-ZONE RME Manual de usuario
(112 paginas)
(112 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(24 paginas)
(24 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(124 paginas)
(124 paginas)
Sensores Watlow EZ-ZONE RMC Manual de usuario
(213 paginas)
(213 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(113 paginas)
(113 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(115 paginas)
(115 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(112 paginas)
(112 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(161 paginas)
(161 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(149 paginas)
(149 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(149 paginas)
(149 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(157 paginas)
(157 paginas)
Sensores Watlow EZ-ZONE ST Manual de usuario
(66 paginas)
(66 paginas)
Sensores Watlow EZ-ZONE ST Manual de usuario
(97 paginas)
(97 paginas)
Sensores Watlow EZ-ZONE ST Manual de usuario
(133 paginas)
(133 paginas)
Sensores Watlow MICRODIN Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales