Watlow EZ-ZONE RMC Manual de usuario Pagina 74
- Pagina / 236
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Watlow EZ-ZONE
®
RMC Module • 71 • Chapter 4 Setup Page
RMC Module • Setup Page
Dis-
play
Parameter Name
Description
Range Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Probus
Index
Parameter
ID
Data
Type
& Read/
Write
[`o;Ct]
[ o.Ct]
Digital Output (7 to 12)
Control
Set the output control
type. This parameter
is only used with PID
control, but can be set
anytime.
[`Ftb] Fixed Time Base (34)
[`utb] Variable Time Base
(103)
Fixed
Time
Base
1204
[offset 30]
0x6A
(106)
7 to 12
2
85 6002 uint
RWES
[`o;tb]
[ o.tb]
Digital Output (7 to 12)
Time Base
Set the time base for
fixed-time-base control.
0.1 to 60.0 seconds 1.0 1202
[offset 30]
0x6A
(106)
7 to 12
3
86 6003 float
RWES
[`o;Lo]
[ o.Lo]
Digital Output (7 to 12)
Low Power Scale
The power output will
never be less than the
value specified and will
represent the value at
which output scaling
begins.
0.0 to 100.0 0.0 1216
[offset 30]
0x6A
(106)
7 to 12
9
87 6009 float
RWES
[`o;hi]
[ o.hi]
Digital Output (7 to 12)
High Power Scale
The power output will
never be greater than
the value specified and
will represent the value
at which output scaling
stops.
0.0 to 100.0 100.0 1218
[offset 30]
0x6A
(106)
7 to 12
A (10)
88 6010 float
RWES
Note:
Some values will be rounded off to fit in the four-character display.
Full values can be read with other interfaces.
Note:
If there is only one instance of a menu, no submenus will appear.
** These parameters/prompts are available in these menus with firmware revisions 6.0 and
above.
R: Read
W: Write
E: EEPROM
S: User Set
- User’s Guide 1
- RMC (Control) Module 1
- Control Module 1
- Safety Information 2
- Warranty 2
- Technical Assistance 2
- Table of Contents 4
- Table of Contents (cont.) 5
- Chapter 1: Overview 7
- Introduction 8
- • 6 • Chapter 1 Overview 9
- Getting Started Quickly 10
- Functions 10
- Function 11
- Slot CSlot C 12
- Module Orientation 13
- Chapter 2: Install and Wire 16
- Dimensions 17
- Power Supplies 18
- Modular Backplane Connector 19
- Module Installation 19
- Removal of the Modular Back 20
- Module Removal 20
- Power and Communications 22
- RMC Module Isolation Diagram 24
- Slot A, B, D, E 25
- RMC Part # Digits 4, 6, 8, 10 26
- RMC Part # Digit 11 is C 28
- Output 2, 4, 6, 8 Switched DC 30
- Safe Operating Area 33
- A Network Using Modbus RTU 38
- Connecting the Modules 39
- [``o;u] Output Value 42
- [`Ain] Value ** 63
- [`Set] Timer Menu 64
- Offset the input reading 68
- 0x68 (104) 68
- 0x70 (112) 76
- Set an offset value for a 87
- 0x80 (128) 95
- 0x83 (131) 95
- 0x82 (130) 100
- 0x7F (127) 100
- Watlow EZ-ZONE 110
- 0x87 (135) 116
- On (63) 119
- Profiling Parameters 131
- [`Pro] Process 148
- Change this value to 152
- Chapter 7: Features 154
- Chapter 7: Features (cont.) 155
- Tuning the PID Parameters 156
- Autotuning with TRU-TUNE+ 157
- Before Tuning 157
- How to Autotune a Loop 157
- • 155 • Chapter 7 Features 158
- • 156 • Chapter 7 Features 159
- Temperature 160
- Control Methods 161
- On-Off Control 162
- Proportional (P) Control 163
- Dead Band 163
- Variable Time Base 164
- Single Set Point Ramping 164
- Cascade Control 165
- Compressor Control 165
- Differential Control 165
- Input 1 Output 1 166
- Resetting a Tripped Limit 167
- Open Loop Detection 168
- Programming the EZ Key/s 168
- Current Sensing 168
- Using Password Security 169
- • 167 • Chapter 7 Features 170
- • 168 • Chapter 7 Features 171
- Software Configuration 172
- • 170 • Chapter 7 Features 173
- • 171 • Chapter 7 Features 174
- Function Block Descriptions 175
- Analog Input Function 176
- -1,999.000 to 9,999.000 176
- Overview 177
- Control Function 179
- Counter Function 181
- Custom Function 181
- Diagnostic Function 181
- Digital Input/Output Function 182
- Global Function 182
- Math Function 187
- Switch Over 189
- Multiply 190
- Absolute Difference 191
- Range Low 193
- Profile Function 194
- Profiling 197
- Unused Step Type 197
- Time Step Type 198
- Rate Step Type 199
- Soak Step Type 200
- State Step Type 201
- Jump Step Type 203
- Wait Time 204
- Subroutine Step Type 205
- End Step Type 206
- Process Value Function 207
- Output Value 207
- Process Value 208
- Setting 212
- Timer Function 214
- One Shot 217
- Retentive 218
- Variable 219
- Chapter 8: Appendix 220
- • 221 • Chapter 8 Appendix 224
- Control Module Specifications 227
- Digital Input 228
- Dry Contact 228
- Output Hardware 229
- Output Hardware (cont.) 229
- • 228 • Chapter 8 Appendix 231
- • 229 • Chapter 8 Appendix 232
- • 230 • Chapter 8 Appendix 233
- • 231 • Chapter 8 Appendix 234
- EZ Zone Series RM 235
- How to Reach Us 236
Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RMC
Sensores Watlow EZ-ZONE RME Manual de usuario
(112 paginas)
(112 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(24 paginas)
(24 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(124 paginas)
(124 paginas)
Sensores Watlow EZ-ZONE RMC Manual de usuario
(213 paginas)
(213 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(113 paginas)
(113 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(115 paginas)
(115 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(112 paginas)
(112 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(161 paginas)
(161 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(149 paginas)
(149 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(149 paginas)
(149 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(157 paginas)
(157 paginas)
Sensores Watlow EZ-ZONE ST Manual de usuario
(66 paginas)
(66 paginas)
Sensores Watlow EZ-ZONE ST Manual de usuario
(97 paginas)
(97 paginas)
Sensores Watlow EZ-ZONE ST Manual de usuario
(133 paginas)
(133 paginas)
Sensores Watlow MICRODIN Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales