Watlow EZ-ZONE RMC Manual de usuario descargar pdf (Pagina 133)

Watlow EZ-ZONE

RMC Module • 130 • Chapter 5 Profiling Page

RMC Module • Profile Page

Display

Parameter Name

Description

Range Default

Modbus

Relative

Address

CIP

Class

Instance

Attribute

hex (dec)

Probus

Index

Parameter

Data Type

& Read/

Write

[hoUr]

Step (1 to 250)

Hours

If step type is Time,

enter time over which

set point changes. If

Soak or State Step,

enter time to maintain

this step.

0 to 99 0 5444

[offset 100]

0x79

(121)

1 to (250)

- - - - 21003 uint

RWE

[Min]

Step (1 to 250)

Step Type Parameters

Minutes

If step type is Time,

enter time over which

set point changes. If

Soak or State Step,

enter time to maintain

this step.

0 to 59 0 5446

[offset 100]

0x79

(121)

1 to (250)

- - - - 21004 uint

RWE

[~SEC]

[ SEC]

Step (1 to 250)

Seconds

If step type is Time,

enter time over which

set point changes. If

Soak or State Step,

enter time to maintain

this step.

0 to 59 0 5448

[offset 100]

0x79

(121)

1 to (250)

- - - - 21005 uint

RWE

[rate]

[rAtE]

Step (1 to 250)

Rate

If step type is Rate,

select the rate for

ramping in degrees or

units per minute.

0 to 9,999.000°F or units

per minute

0 to 5,555.000°C per min-

ute

0.0 5450

[offset 100]

0x79

(121)

1 to (250)

- - - - 21006 float

RWE

[`P;E1]

[P.E1]

Step (1 to 250)

Step Wait For Pro-

cess Enable 1

If step type is Wait

for Process or Event,

select whether process

value must be Less

Than or Greater Than

the value of Wait for

Process to satisfy the

wait-for condition.

[`oFF] Off (62)

[``L;t] Less Than (1436)

[``g;t] Greater Than

(1435)

Off 5510

[offset 100]

0x79

(121)

1 to (250)

0x24 (36)

- - - - 21036 uint

RWE

[W;P1]

[W.P1]

Step (1 to 250)

Wait For Process 1

Enter a value that

must be satisfied

which is specified by

Source E in Profile

Setup.

-1,999.000 to 9,999.000°F

or units

-1,128.000 to 5,537.000°C

0.0°F or

units

-18.0°C

5460

[offset 100]

0x79

(121)

1 to (250)

0xB (11)

- - - - 21011 float

RWE

[`P;E2]

[P.E2]

Step (1 to 250)

Step Wait For Pro-

cess Enable 2

If step type is Wait

for Process or Event,

select whether process

value must be Less

Than or Greater Than

the value of Wait for

Process to satisfy the

wait-for condition.

[`oFF] Off (62)

[``L;t] Less Than (1436)

[``g;t] Greater Than

(1435)

Off 5512

[offset 100]

0x79

(121)

1 to (250)

0x25 (37)

- - - - 21037 uint

RWE

Note: Some values will be rounded off to fit in the four-character display. Full values

can be read with other interfaces.

If there is only one instance of a menu, no submenus will appear.

R: Read

W: Write

E: EEPROM

S: User Set

1 2 ... 128 129 130 131 132 133 134 135 136 137 138 ... 235 236

Comentarios a estos manuales

Sin comentarios

Watlow EZ-ZONE RMC Manual de usuario Pagina 133

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RMC