Watlow EZ-ZONE RMC Manual de usuario descargar pdf (Pagina 88)

Watlow EZ-ZONE

RMC Module • 85 • Chapter 4 Setup Page

RMC Module • Setup Page

Dis-

play

Parameter Name

Description

Range Default

Modbus

Relative

Address

CIP

Class

Instance

Attribute

hex (dec)

Probus

Index

Parameter

Data

Type

& Read/

Write

[`is;a]

[ iS.A]

Alarm (1 to 8)

Source Instance

Set the instance of the

function selected above.

1 or 250 1 1774

[offset 60]

0x6D

(109)

1 to 8

0x12 (18)

22 9018 uint

RWES

[`S2;A]

[ SZ.A]

Alarm (1 to 8)

Source Zone

Set the zone of the func-

tion selected above.

0 or 16 0 1788

[offset 60]

0x6D

(109)

1 to 8

0x19 (25)

- - - - 9025 uint

RWES

[loop]

[LooP]

Alarm (1 to 4)

Control Loop

Set the instance of the

Set Point Closed, Control

Loop, that will be refer-

enced by the deviation

alarm.

1 to 250 1 1784

[offset 60]

0x6D

(109)

1 to 8

0x17 (23)

23 9023 uint

RWES

[`A;hy]

[ A.hy]

Alarm (1 to 8)

Hysteresis

Set the hysteresis for an

alarm. This determines

how far into the safe

region the process value

needs to move before the

alarm can be cleared.

0.001 to 9,999.000°F or units

0.001 to 5,555.000°C

1.0°F or

units

1.0°C

1744

[offset 60]

0x6D

(109)

1 to 8

24 9003 float

RWES

[`A;Lg]

[ A.Lg]

Alarm (1 to 8)

Logic

Select what the output

condition will be during

the alarm state.

[`AL;C] Close On Alarm (17)

[`AL;o] Open On Alarm (66)

Close On

Alarm

1748

[offset 60]

0x6D

(109)

1 to 8

25 9005 uint

RWES

[`A;Sd]

[ A.Sd]

Alarm (1 to 8)

Sides

Select which side or

sides will trigger this

alarm.

[both] Both (13)

[high] High (37)

[LoW] Low (53)

Both 1746

[offset 60]

0x6D

(109)

1 to 8

26 9004 uint

RWES

[`A;Lo]

[ A.Lo]

Alarm (1 to 8)

Low Set Point **

If Alarm Type (Setup

Page, Alarm Menu) is

set to:

process - set the pro-

cess value that will

trigger a low alarm.

deviation - set the

span of units from the

closed loop set point

that will trigger a low

alarm. A negative set

point represents a

value below closed loop

set point. A positive

set point represents a

value above closed loop

set point.

-1,999.000 to 9,999.000°F or

units

-1,128.000 to 5,537.000°C

32.0°F

or units

0.0°C

1742

[offset

60]

0x6D

(109)

1 to 8

18 9002 float

RWES

Note:

Some values will be rounded off to fit in the four-character display.

Full values can be read with other interfaces.

Note:

If there is only one instance of a menu, no submenus will appear.

** These parameters/prompts are available in these menus with firmware revisions 6.0 and

above.

R: Read

W: Write

E: EEPROM

S: User Set

1 2 ... 83 84 85 86 87 88 89 90 91 92 93 ... 235 236

Comentarios a estos manuales

Sin comentarios

Watlow EZ-ZONE RMC Manual de usuario Pagina 88

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RMC