Watlow EZ-ZONE RMC Manual de usuario descargar pdf (Pagina 85)

Watlow EZ-ZONE

RMC Module • 82 • Chapter 4 Setup Page

RMC Module • Setup Page

Dis-

play

Parameter Name

Description

Range Default

Modbus

Relative

Address

CIP

Class

Instance

Attribute

hex (dec)

Probus

Index

Parameter

Data

Type

& Read/

Write

[`S2;A]

[ SZ.A]

Output Digital (1 to 8)

Source Zone A

Set the instance of the

function selected above.

0 to 16 0 1042

[offset 30]

0x6A

(106)

1 to 8

0xC (12)

- - - - 6012 uint

RWES

[`o;Ct]

[ o.Ct]

Output Digital (1 to 8)

Control

Set the output control

type. This parameter

is only used with PID

control, but can be set

anytime.

[`Ftb] Fixed Time Base (34)

[`utb] Variable Time Base

(103)

Fixed

Time

Base

1022

[offset 30]

0x6A

(106)

1 to 8

- - - - 6002 uint

RWES

[`o;tb]

[ o.tb]

Output Digital (1 to 8)

Time Base

Set the time base for

fixed-time-base control.

0.1 to 60.0 seconds (solid-state

relay or switched dc)

5.0 to 60.0 seconds (mechani-

cal relay or NO-ARC power

control)

1.0 sec.

[SSR &

sw dc]

20.0 sec.

[mech,

relay,

NO-

ARC]

1024

[offset 30]

0x6A

(106)

1 to 8

- - - - 6003 float

RWES

[`o;Lo]

[ o.Lo]

Output Digital (1 to 8)

Low Power Scale

The power output will

never be less than the

value specified and will

represent the value at

which output scaling

begins.

0.0 to 100.0% 0.0% 1036

[offset 30]

0x6A

(106)

1 to 8

- - - - 6009 float

RWES

[`o;hi]

[ o.hi]

Output Digital (1 to 8)

High Power Scale

The power output will

never be greater than

the value specified and

will represent the value

at which output scaling

stops.

0.0 to 100.0% 100.0% 1038

[offset 30]

0x6A

(106)

1 to 8

0xA (10)

- - - - 6010 float

RWES

[`o;ty]

[ o.ty]

Output Process (1, 3, 5

or 7)

Type

Select whether the pro-

cess output will operate

in volts or milliamps.

[uoLt] Volts (104)

[`MA] Milliamps (112)

Volts 840 (1)

888 (3)

936 (5)

984 (7)

0x76 (118)

1 to 4

95 18001 uint

RWES

Note:

Some values will be rounded off to fit in the four-character display.

Full values can be read with other interfaces.

Note:

If there is only one instance of a menu, no submenus will appear.

** These parameters/prompts are available in these menus with firmware revisions 6.0 and

above.

R: Read

W: Write

E: EEPROM

S: User Set

1 2 ... 80 81 82 83 84 85 86 87 88 89 90 ... 235 236

Comentarios a estos manuales

Sin comentarios

Watlow EZ-ZONE RMC Manual de usuario Pagina 85

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RMC