Watlow EZ-ZONE RMC Manual de usuario descargar pdf (Pagina 179)

Watlow EZ-ZONE

RMC Module • 176 • Chapter 7 Features

Control Function

Control

Overview

Instances - 1 to 4 per RMC

Control Mode

Remote Set Point Enable

Remote Set Point Type

User Failure Action

Loop Error Clear Request

Input Error Failure

Fixed Power

Open Loop Detect Enable

Open Loop Detect Time

Open Loop Detect Deviation

Ramp Action

Ramp Scale

Ramp Rate

Proﬁling Enable

Closed Loop Low Set Point

Set Point Open Limit Low

Closed Loop High Set Point

Set Point Open Limit High

Heat Algorithm

Cool Algorithm

TRU-TUNE+ Enable

Autotune Aggressiveness

Peltier Delay

TRU-TUNE+ Band

TRU-TUNE+ Gain

Cool Output Curve

Autotune Set Point

Autotune

Closed Loop Set Point

Idle Set Point

Heat Proportional Band

Cool Proportional Band

Heat Hysteresis

Cool Hysteresis

Deadband

Open Loop Set Point

Cool Power

Heat Power

Tune Status

Loop Error

Closed Loop Set Point

Open Loop Set Point

Loop Power

Process Value Active

Source Function A

Source Instance A

Source Zone A

Source Error A

Source Function B

Source Instance B

Source Zone B

Source Error B

Time Integral

Time Derivative

[SFn;A] Source Function A : Analog Input, Process Value

`[h;Ag] Heat Algorithm : Off, PID, On/Off

[`C;Ag] Cool Algorithm : Off, PID, On/Off

[t;tUn] TRU-TUNE+ Enable : No, Yes

[t;bnd] TRU-TUNE+ Band : 0 to 100

[`t;gn] TRU-TUNE+ Gain : 1 to 6

[t;Agr] Autotune Aggressiveness : Under, Critical, Over

[`r;En] Remote Set Point Enable : No, Yes

[`Si;b] Source Instance B (Remote Set Point Source Instance) : 1 to 250

[`S2;b] Source Zone B : 0 to 16

[MAn] Fixed Power : -100.0 to 100.0 %

[`L;dE] Open Loop Detect Enable : No, Yes

[`L;dt] Open Loop Detect Time : 0 to 3,600 seconds

[``rP] Ramp Action : Off, Startup, Set Point, Both

[`r;SC] Ramp Scale : Hours, Minutes

[`r;En] Remote Set Point Enable : No, Yes

[`C;M] Control Mode : Off, Auto, Manual

[A;tSP] Autotune Set Point : 50 to 200 %

[`AUt] Autotune : No, Yes

[`C;SP] Closed Loop Set Point : -1,999.000 to 9,999.000

[`id;S] Idle Set Point : -1,999.000 to 9,999.000

[`h;Pb] Heat Proportional Band : 0.001 to 9,999.000

[`h;hy] Heat Hysteresis : 0.001 to 9,999.000

[`C;Pb] Cool Proportional Band : 0.001 to 9,999.000

[`C;hy] Cool Hysteresis : 0.001 to 9,999.000

[``ti] Time Integral : 0 to 9,999 seconds

[``td] Time Derivative : 0 to 9,999 seconds

`[C;Cr] Cool Output Curve : Off, Non-linear curve 1, Non-linear curve 2

[`r;ty] Remote Set Point Type : Auto, Manual

[`L;SP] Low Set Point : -1,999.000 to 9,999.000

[`h;SP] High Set Point : -1,999.000 to 9,999.000

[SP;Lo] Set Point Open Limit Low : -100.0 to 100.0 %

[SP;hi] Set Point Open Limit High : -100.0 to 100.0 %

[`L;dd] Open Loop Detect Deviation : -1,999.000 to 9,999.000

[`r;rt] Ramp Rate : 0.000 to 9,999.000

[Pro;E] Proﬁling Enable: No, Yes

[``db] Deadband : -1,000.000 to 1,000.000

[`o;SP] Open Loop Set Point : -100.0 to 100.0 %

[`iS;A] Source Instance A : (not changeable)*

[LooP] Loop Menu

[`SEt] Setup Page

[LooP] Loop Menu

[oPEr] Operation Page

[`P;dL] Peltier Delay : 0.0 to 5.0

Note: Control Loop primary source instance must match

Process Value or Analog Input instance.

Loop Power : -100.0 to 100.0 %

Loop Error: None, Open Loop, Reversed Sensor

Loop Error Clear Request : Ignore, Clear

Tune Status : Off, Cross 1 Positive, Cross 1 Negative,

Cross 2 Positive, Cross 2 Negative, Cross 3 Positive,

Cross 3 Negative, Measuring Max, Measuring Min,

Calculating, Complete, Timeout

[C;MA] Control Mode Active : Off, Auto, Manual

[`h;Pr] Heat Power : 0.0 to 100.0 %

[`C;Pr] Cool Power : 0.0 to 100.0 %

[`C;SP] Closed Loop Set Point : -1,999.000 to 9,999.000

[`Pu;A] Process Value Active : -1,999.000 to 9,999.000

[Mon] Monitor Menu

[oPEr] Operation Page

Control Mode Active

[SFn;b] Source Function B : (Remote Set Point Source) : None, Analog

Input, Current, Cool Power, Heat Power, Power, Linearization,

Math, Process Value, Set Point Closed, Set Point Open, Variable

[fail] Input Error Failure : Off, Bumpless Transfer, Manual Power,

User

[`Ufa] User Failure Action : Off, Bumpless Transfer, Manual Power,

User

1 2 ... 174 175 176 177 178 179 180 181 182 183 184 ... 235 236

Comentarios a estos manuales

Sin comentarios

Watlow EZ-ZONE RMC Manual de usuario Pagina 179

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RMC