Watlow EZ-ZONE RM Limit Module Rev C Manual de usuario Pagina 97
- Pagina / 127
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Watlow EZ-ZONE
®
RML Module • 94 • Chapter 6 Features
Limit Function
This function uses a dedicated input and the output
will change state when Source A exceeds limit set
points. The limit, when tripped, must be manually
cleared to reset the output and clear the message.
The Analog Input and mechanical relay output are
dedicated to each limit loop and are located in same
module.
Limit
Overview
Instances - 0 to 12 per RML
Source Function A
Source Instance A
Source Error A
Set Point (Maximum) High Limit
Limit Hysteresis
Limit Sides
Limit Clear Request
Set Point (Minimum) Low Limit
Limit High Set Point
Limit State
Limit Status
Output Value
Limit Low Set Point
[L;hy] Limit Hysteresis : 0.001 to 9,999.000
[SP;Lh] Set Point (Maximum) High Limit : -1,999.000 to 9,999.000
[SP;LL] Set Point (Minimum) Low Limit : -1,999.000 to 9,999.000
[`LL;S] Limit Low Set Point : -1,999.000 to 9,999.000
[`Lh;S] Limit High Set Point : -1,999.000 to 9,999.000
[L;Sd] Limit Sides : Both, High, Low
Limit Status : Fail, Safe
Output Value : On, Off
[LiM] Limit Menu
[`SEt] Setup Page
[LiM] Limit Menu
[oPEr] Operation Page
Limit Message
Limit Message : Limit High, Limit Low, Limit Error
[`lh;s] Limit High Set Point : -1,999.000 to 9,999.000
[`ll;s] Limit Low Set Point: -1,999.000 to 9,999.000
[Sfn;a] Source Function: None, Digital I/O, Function Key, Variable
[`si;a] Source Instance: 1 to 250
[`s2;a] Source Zone: 0 to 16
[`lCr] Limit Clear Request: Ignore or Clear
[`l;st] Limit State: Off, None, Limit High, Limit Low, Error
[`lCr] Limit Clear Request
[`l;st] Limit State: Off, None, Limit High, Limit Low, Error
Linearization Function
This function will take an analog Source A and re-
linearize using a 10-point offset, then add Offset and
produce an Output Value.
An error, when read, can indicate any of the follow-
ing: None, Open, Shorted, Measurement Error, Bad
Cal Data, Ambient Error, RTD Error, Fail, Math Er-
ror, Not Sourced, Stale
Linearization
Overview
Instances - 16 per RML
Units
Function
Input Point 1
Output Point 1
Output Point 2
Output Point 3
Output Point 4
Output Point 5
Output Point 6
Output Point 7
Output Point 8
Output Point 9
Output Point 10
Offset
Input Point 2
Input Point 3
Input Point 4
Input Point 5
Input Point 6
Input Point 7
Input Point 8
Input Point 9
Input Point 10
[`Su;A] Source Value A : -1,999.000 to 9,999.000
[``o;u] Output Value : -1,999.000 to 9,999.000
[`Lnr] Linearization Menu
[oPEr] Operation Page
[SFn;A] Source Function A : None, Analog Input, Current, Cool Power, Heat Power,
Power, Linearization, Math, Process Value, Set Point Closed, Set Point Open,
Variable
[`S2;A] Source Zone A : 0 to 16
[`Si;A] Source Instance A : 1 to 250
[``Fn] Function : Off, Interpolated, Stepped
[oFSt] Offset : -1,999.000 to 9,999.000
[`iP;1] Input Point 1 : -1,999.000 to 9,999.000
[`iP;2] Input Point 2 : -1,999.000 to 9,999.000
[`iP;3] Input Point 3 : -1,999.000 to 9,999.000
[`iP;4] Input Point 4 : -1,999.000 to 9,999.000
[`iP;5] Input Point 5 : -1,999.000 to 9,999.000
[`iP;6] Input Point 6 : -1,999.000 to 9,999.000
[`iP;7] Input Point 7 : -1,999.000 to 9,999.000
[`iP;8] Input Point 8 : -1,999.000 to 9,999.000
[`iP;9] Input Point 9 : -1,999.000 to 9,999.000
[iP;10] Input Point 10 : -1,999.000 to 9,999.000
[`oP;1] Output Point 1 : -1,999.000 to 9,999.000
[`oP;2] Output Point 2 : -1,999.000 to 9,999.000
[`oP;3] Output Point 3 : -1,999.000 to 9,999.000
[`oP;4] Output Point 4 : -1,999.000 to 9,999.000
[`oP;5] Output Point 5 : -1,999.000 to 9,999.000
[`oP;6] Output Point 6 : -1,999.000 to 9,999.000
[`oP;7] Output Point 7 : -1,999.000 to 9,999.000
[`oP;8] Output Point 8 : -1,999.000 to 9,999.000
[`oP;9] Output Point 9 : -1,999.000 to 9,999.000
[oP;10] Output Point 10 : -1,999.000 to 9,999.000
[`Lnr] Linearization
[`SEt] Setup Page
Source Function A
Source Instance A
Source Zone A
Source Error A
Output Value
Source Value A
Error
[Unit] Units : Source, None, Absolute Temperature, Relative Temperature, Power,
Process, Relative Humidity
Source Function A
Source Instance A
Source Zone A
Source Error A
Linearization
Off
Output Value
Source Value A
Error
Units
Function
Input Point 1
Output Point 1
Output Point 2
Output Point 3
Output Point 4
Output Point 5
Output Point 6
Output Point 7
Output Point 8
Output Point 9
Output Point 10
Offset
Input Point 2
Input Point 3
Input Point 4
Input Point 5
Input Point 6
Input Point 7
Input Point 8
Input Point 9
Input Point 10
Output Value equals Source A Value
- User’s Guide 1
- RM Limit Module 1
- RM Limit Module 1
- Safety Information 2
- Warranty 2
- Technical Assistance 2
- Table of Contents 4
- Table of Contents (cont.) 5
- Chapter 1: Overview 6
- Introduction 7
- A Conceptual View of the RML 8
- • 6 • Chapter 1 Overview 9
- Module Orientation 10
- Getting Started Quickly 11
- Chapter 2: Install and Wire 14
- Dimensions 14
- Power Supplies 16
- Modular Backplane Connector 17
- Module Installation 17
- Removal of the Modular Back 18
- Module Removal 18
- Limit Module (RMLx-xxxx-xxxx) 19
- RML System Isolation Blocks 22
- Communications 23
- Low Power 23
- Inputs 1 through 12 RTD 24
- Digital Outputs 1 - 6 25
- Process Inputs 1 through 12 25
- DC90-60C0-0000 26
- RML Part # Digit 7, 8 is J 27
- RML Part # Digit 8 is B 27
- Quencharc Wiring Example 28
- Model 485TB-2W 29
- B B electronics 29
- EZKB-_A_ _-_ _ _ _ 30
- Power Supply 31
- Low Voltage 31
- Class 2 31
- Chapter 3: Operations Pages 34
- Chapter 4: Setup Pages 44
- Navigating the Setup Page 44
- [`Set] Timer Menu 45
- 0x86 (134) 54
- 0x83 (131) 58
- 0x82 (130) 60
- 0x7F (127) 62
- 0x66 (102) 74
- Chapter 5: Factory Pages 76
- Navigating the Factory Page 76
- Chapter 6: Features 81
- Calibration Offset 82
- Calibration 82
- Filter Time Constant 83
- Sensor Selection 83
- Scale High and Scale Low 83
- Temperature 84
- Alarm Silencing 85
- Alarm Blocking 85
- Lockout Menu 85
- Using Password Security 86
- • 84 • Chapter 6 Features 87
- Software Configuration 88
- • 86 • Chapter 6 Features 89
- • 87 • Chapter 6 Features 90
- Function Block Descriptions 91
- -1,999.000 to 9,999.000 92
- Input Error Latching 93
- Counter Function 95
- Custom Function 95
- Diagnostic Function 95
- Digital Input/Output Function 96
- Global Function 96
- Input Point 2 97
- Logic Function 98
- Watlow EZ-ZONE 100
- Math Function 101
- Overview 102
- Switch Over 103
- Multiply 104
- Absolute Difference 105
- Output Function 106
- Security Function 107
- Timer Function 108
- One Shot 111
- Retentive 112
- Variable 113
- Chapter 7: Appendix 114
- RML Specifications 120
- • 120 • Appendix 123
- Electrical Slope 80 124
- • 122 • Appendix 125
- EZ Zone Series RM 126
- How to Reach Us 127
Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RM Limit Module Rev C
Sensores Watlow EZ-ZONE RMA Modul Manual de usuario
(79 paginas)
(79 paginas)
Sensores Watlow EZ-ZONE RMA Modul Manual de usuario
(79 paginas)
(79 paginas)
Sensores Watlow EZ-ZONE RM Manual de usuario
(155 paginas)
(155 paginas)
Sensores Watlow EZ-ZONE RMA Modul Manual de usuario
(80 paginas)
(80 paginas)
Sensores Watlow EZ-ZONE RMA Modul Manual de usuario
(79 paginas)
(79 paginas)
Sensores Watlow EZ-ZONE RMA Modul Manual de usuario
(79 paginas)
(79 paginas)
Sensores Watlow EZ-ZONE RMC Manual de usuario
(213 paginas)
(213 paginas)
Sensores Watlow EZ-ZONE RMC Manual de usuario
(213 paginas)
(213 paginas)
Sensores Watlow EZ-ZONE RMC Manual de usuario
(213 paginas)
(213 paginas)
Sensores Watlow EZ-ZONE RMC Manual de usuario
(236 paginas)
(236 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(112 paginas)
(112 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(24 paginas)
(24 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(124 paginas)
(124 paginas)
Sensores Watlow EZ-ZONE RMC Manual de usuario
(213 paginas)
(213 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(113 paginas)
(113 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales