Watlow EZ-ZONE RM Limit Module Rev C Manual de usuario descargar pdf (Pagina 47)

Watlow EZ-ZONE

RML Module • 44 • Chapter 4 Setup Page

RM Limit Module • Setup Page

Display

Parameter Name

Description

Range Default

Modbus

Relative

Address

CIP

Class

Instance

Attribute

hex (dec)

Probus

Index

Parameter

Data

Type

Read/

Write

[`P;EL]

[ P.EL]

Analog Input (1 to 12)

Process Error Low

If the process value drops

below this value, it will

trigger an input error.

-100.0 to 1,000.0 0.0 470

[offset 90]

0x68 (104)

1 to 0xC

(12)

0x1F (31)

11 4031 float

RWES

[``t;C]

[ t.C]

Analog Input (1 to 12)

Thermistor Curve

Select a curve to apply to

the thermistor input.

[```A] Curve A (1451)

[```b] Curve B (1452)

[```C] Curve C (1453)

[CUSt] Custom (180)

Curve A 484

[offset 90]

0x68 (104)

1 to 0xC

(12)

0x26 (38)

- - - - 4038 uint

RWES

[``r;r]

[ r.r]

Analog Input (1 to 12)

Resistance Range

Set the maximum resis-

tance of the thermistor

input.

[```5] 5K (1448)

[``10] 10K (1360)

[``20] 20K (1361)

[``40] 40K (1449)

40K 432

[offset 90]

0x68 (104)

1 to 0xC

(12)

0x25 (37)

- - - - 4037 uint

RWES

[`FiL]

[ FiL]

Analog Input (1 to 12)

Filter

Filtering smooths out the

process signal to both the

display and the input. In-

crease the time to increase

filtering.

0.0 to 60.0 seconds 0.5 386

[offset 90]

0x68 (104)

1 to 0xC

(12)

0xE (14)

12 4014 float

RWES

[`i;Er]

[ i.Er]

Analog Input (1 to 12)

Error Latching

Turn input error latching

on or off. If latching is on,

errors must be manually

cleared.

[`off] Off (62)

[``on] On (63)

Off 414

[offset 90]

0x68 (104)

1 to 0xC

(12)

0x1C (28)

- - - - 4028 uint

RWES

[`dEC]

[ dEC]

Analog Input (1 to 12)

Display Precision

Set the precision of the dis-

played value.

[```0] Whole (105)

[``0;0] Tenths (94)

[`0;00] Hundredths (40)

[0;000] Thousandths (96)

Whole 398

[offset 90]

0x68 (104)

1 to 0xC

(12)

0x14 (20)

- - - - 4020 uint

RWES

[`i;Ca]

[ i.CA]

Analog Input (1 to 12)

Calibration Offset

Offset the input reading to

compensate for lead wire

resistance or other factors

that cause the input read-

ing to vary from the actual

process value.

-1,999.000 to 9,999.000°F or

units

-1,110.555 to 5,555.000°C

0.0 432

[offset 90]

0x68 (104)

1 to 0x10

(16)

0x0C (12

- - - - 4012 float

RWES

[``Ain]

[ Ain]

Analog Input (1 to 12)

Process Value

View the process value.

-1,999.000 to 9,999.000°F or

units

-1,128.000 to 5,537.000°C

- - - - 410

[offset 90]

0x68 (104)

1 to 0xC

(12)

0 4001 float

RWES

[`i;Er]

[ i.Er]

Analog Input (1 to 12)

Error Status

View the cause of the most

recent error. If the

[Attn]

message is

[Er;i1]

[Er;i2]

, this parameter

will display the cause of

the input error.

[nonE] None (61)

[OPEn] Open (65)

[Shrt] Shorted (127)

[`E;M] Measurement Error

(149)

[E;CAL] Bad Calibration Data

(139)

[Er;Ab] Ambient Error (9)

[E;;Rtd] RTD Error (141)

[FAiL] Fail (32)

[Nsrc] Not Sourced (246)

None 412

[offset 90]

0x68 (104)

1 to 0xC

(12)

1 4002 float

RWES

Note: Some values will be rounded off to fit in the four-character display.

Full values can be read with other interfaces.

If there is only one instance of a menu, no submenus will appear.

R: Read

W: Write

E: EEPROM

S: User

Set

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 126 127

Comentarios a estos manuales

Sin comentarios

Watlow EZ-ZONE RM Limit Module Rev C Manual de usuario Pagina 47

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RM Limit Module Rev C