Watlow EZ-ZONE RME Manual de usuario Pagina 98
- Pagina / 124
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Watlow EZ-ZONE
®
RME Module • 95 • Chapter 6 Features
Digital Input/Output Function
Note:
Input value is passed to any specified digital input source
when programmed as input by that function block.
Output value determine by Function Block driving this
output.
Digital I/O Value : On, Off
An error, when read, can indicate any of the following:
None, Open, Shorted, Measurement Error, Bad Cal Data,
Ambient Error, RTD Error, Fail, Math Error, Not Sourced,
Stale
Output Function
Output Function Instance
Source Zone A
Output Low
Power Scale
Output Time Base
Output Control
Output High
Power Scale
Direction
[`S2;A] Source Zone A : 0 to 16
[`do;S] Output State : On, Off
[`o;Ct] Output Control : Fixed Time Base, Variable Time Base
[`o;Lo] Output Low Power Scale : 0.0 to 100.0 %
[`dir] Direction : Output, Input Contact, Input Voltage
[`o;hi] Output High Power Scale : 0.0 to 100.0 %
[`o;tb] Output Time Base : 0.1 to 60.0 seconds
[``Fi] Output Function Instance : 1 to 250
[`di;S] Input State : On, Off
Output State
Digital I/O Value
Error
[`dio] Digital I/O Menu
[`SEt] Operation Page
[`dio] Digital I/O Menu
[`SEt] Setup Page
[``Fn] Output Function : Off, Analog Input, Alarm, Cool Power, Heat
Power, Compare, Counter, Digital I/O, Profile Event Out A to H,
Function Key, Logic, Linearization, Math, Process Value, Special
Function Output 1 to 4, Timer, Variable
Digital IO
Overview
Instances - 0, 6, 12, 18 or 24 per RME
Digital IO as Input
Input State
Digital I/O Value
Error
Digital Input Value
Output Low Power Scale
Output Time Base
Output Control
Output High
Power Scale
Direction
Output Function
Output Function Instance
Source Zone A
Output Low Power Scale
Output Time Base
Output Control
Output High Power Scale
Direction
Output State
Digital I/O Value
Error
Digital IO as Output
Global Function
This function allows the user to change display units
as well as save and restore user settings.
Global
Overview
Instances - 1 per RME
[AC;Lf] AC Line Frequency : 50 Hz, 60 Hz
[d;PrS] Display Pairs : 1 to 10
[USr;S] User Settings Save : None, User Set 1, User Set 2
[USr;r] User Settings Restore : None, User Set 1, User Set 2, Factory
[`C_F] Display Units : F, C
AC Line Frequency
User Settings Restore
Display Units
User Settings Save
Display Plairs
[gLbL] Global Menu
[`SEt] Setup Page
Output Value
Linearization Function
This function will take an analog Source A and re-
linearize using a 10-point offset, then add Offset and
produce an Output Value.
An error, when read, can indicate any of the follow-
ing: None, Open, Shorted, Measurement Error, Bad
Cal Data, Ambient Error, RTD Error, Fail, Math Er-
ror, Not Sourced, Stale
Linearization
Overview
Instances - 8 per RME
Units
Function
Input Point 1
Output Point 1
Output Point 2
Output Point 3
Output Point 4
Output Point 5
Output Point 6
Output Point 7
Output Point 8
Output Point 9
Output P
oint 10
Offset
Input Point 2
Input Point 3
Input Point 4
Input Point 5
Input Point 6
Input Point 7
Input Point 8
Input Point 9
Input Point 10
[SFn;A] Source Function A : None, Analog Input, Current, Cool Power, Heat Power,
Power, Linearization, Math, Process Value, Set Point Closed, Set Point Open, Variable
[`S2;A] Source Zone A : 0 to 16
[`Si;A] Source Instance A : 1 to 250
[``Fn] Function : Off, Interpolated, Stepped
[`iP;1] Input Point 1 : -1,999.000 to 9,999.000
[`iP;2] Input Point 2 : -1,999.000 to 9,999.000
[`iP;3] Input Point 3 : -1,999.000 to 9,999.000
[`iP;4] Input Point 4 : -1,999.000 to 9,999.000
[i`P;5] Input Point 5 : -1,999.000 to 9,999.000
[`iP;6] Input Point 6 : -1,999.000 to 9,999.000
[`iP;7] Input Point 7 : -1,999.000 to 9,999.000
[`iP;8] Input Point 8 : -1,999.000 to 9,999.000
[`iP;9] Input Point 9 : -1,999.000 to 9,999.000
[iP;10] Input Point 10 : -1,999.000 to 9,999.000
[`oP;1] Output Point 1 : -1,999.000 to 9,999.000
[`oP;2] Output Point 2 : -1,999.000 to 9,999.000
[`oP;3] Output Point 3 : -1,999.000 to 9,999.000
[`oP;4] Output Point 4 : -1,999.000 to 9,999.000
[`oP;5] Output Point 5 : -1,999.000 to 9,999.000
[`oP;6] Output Point 6 : -1,999.000 to 9,999.000
[`oP;7] Output Point 7 : -1,999.000 to 9,999.000
[`oP;8] Output Point 8 : -1,999.000 to 9,999.000
[`oP;9] Output Point 9 : -1,999.000 to 9,999.000
[oP;10] Output Point 10 : -1,999.000 to 9,999.000
[Unit] Units : Source, None, Absolute Temperature, Relative Temperature, Power,
Process, Relative Humidity
[`Lnr] Linearization
[`SEt] Setup Page
Source Function A
Source Instance A
Source Zone A
Source Error A
Output Value
Source Value A
Error
- User’s Guide 1
- RME (Expansion) Module 1
- Expansion Module 1
- Safety Information 2
- Warranty 2
- Technical Assistance 2
- Return Material Authorization 2
- Table of Contents 4
- Table of Contents (cont.) 5
- Chapter 1: Overview 6
- Introduction 7
- • 5 • Chapter 1 Overview 8
- What is an Instance? 9
- Functions 9
- Function 10
- (RUI) and a PC 11
- Module Orientation 12
- Chapter 2: Install and Wire 14
- Dimensions 15
- Power Supplies 16
- Modular Backplane Connector 17
- Module Installation 17
- Removal of the Modular Back 18
- Module Removal 18
- RME System Isolation Blocks 22
- Communications 23
- Digital Inputs 1 to 24 24
- Digital Outputs 1 to 24 24
- 1 to 24) 25
- Switched DC to DIN-A-MITE 25
- Quencharc Wiring Example 26
- Dual 10A SSR Outputs 1-4 26
- Warning: ç 29
- RM System Connections 30
- 31
- Operation Page Parameters 33
- Set an offset to be applied 36
- Setup Page Parameters 42
- [`Set] Timer Menu 43
- 0x6A (106) 44
- 0x6E (110) 46
- 0x76 (118) 49
- 0x80 (128) 57
- 0x83 (131) 57
- 0x82 (130) 60
- 0x7F (127) 62
- 0x7D (125) 71
- 0x87 (135) 77
- 0x66 (102) 79
- Factory Page Parameters 80
- Chapter 6: Features 84
- CAUTION: 85
- Retransmit 86
- • 84 • Chapter 6 Features 87
- Programming the EZ Key/s 88
- Using Password Security 89
- • 87 • Chapter 6 Features 90
- Software Configuration 91
- • 89 • Chapter 6 Features 92
- • 90 • Chapter 6 Features 93
- Function Block Descriptions 94
- Compare Function 95
- Overview 97
- Digital Input/Output Function 98
- Global Function 98
- Linearization Function 98
- Input Point 2 98
- Logic Function 99
- Watlow EZ-ZONE 100
- Math Function 102
- Output Value 102
- : -1,999.000 to 9,999.000 103
- Switch Over 104
- Differential 105
- Absolute Difference 106
- Sample and Hold 107
- Dewpoint 107
- Security Function 108
- Special Output Function 108
- Timer Function 109
- One Shot 112
- Variable Function 114
- Chapter 7: Appendix 115
- RME Specifications 117
- • 116 • Chapter 7 Appendix 119
- • 117 • Chapter 7 Appendix 120
- • 118 • Chapter 7 Appendix 121
- • 119 • Chapter 7 Appendix 122
- EZ Zone Series RM 123
- How to Reach Us 124
Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RME
Sensores Watlow EZ-ZONE RMC Manual de usuario
(213 paginas)
(213 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(113 paginas)
(113 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(115 paginas)
(115 paginas)
Sensores Watlow EZ-ZONE RME Manual de usuario
(112 paginas)
(112 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(161 paginas)
(161 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(149 paginas)
(149 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(149 paginas)
(149 paginas)
Sensores Watlow EZ-ZONE RMH Manual de usuario
(157 paginas)
(157 paginas)
Sensores Watlow EZ-ZONE ST Manual de usuario
(66 paginas)
(66 paginas)
Sensores Watlow EZ-ZONE ST Manual de usuario
(97 paginas)
(97 paginas)
Sensores Watlow EZ-ZONE ST Manual de usuario
(133 paginas)
(133 paginas)
Sensores Watlow MICRODIN Manual de usuario
(24 paginas)
(24 paginas)
Sensores Watlow MICRODIN Manual de usuario
(24 paginas)
(24 paginas)
Sensores Watlow MICRODIN Manual de usuario
(106 paginas)
(106 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales