Watlow EZ-ZONE RME Manual de usuario descargar pdf (Pagina 42)

Watlow EZ-ZONE

RME Module • 39 • Chapter 4 Setup Page

Chapter 4: Setup Pages

[`dio]

[`Set] Digital Input/Output Menu

[```1]

[`dio] Digital Input/Output (1 to 24)

[`dir] Direction

[``Fn] Function

[``Fi] Function Instance

[`S2;A] Source Zone A

[`o;Ct] Control

[`o;tb] Time Base

[`o;Lo] Low Power Scale

[`o;hi] High Power Scale

[`ACt]

[`Set] Action Menu

[```1]

[`ACt] Action (1 to 8)

[``Fn] Function

[``Fi] Function Instance

[SFn;A] Source Function A

[`Si;A] Source Instance A

[`S2;A] Source Zone A

[`LEu] Active Level

[otpt]

[`Set] Output Menu

[```1]

[otpt] Output (1 to 24)

[``Fn] Function

[``Fi] Function Instance

[`S2;A] Source Zone A

[`o;Ct] Control

[`o;tb] Time Base

[`o;Lo] Low Power Scale

[`o;hi] High Power Scale

[otpt] Output 1-3, 7-9, 13-15, 19-21

process

[`o;ty] Type

[``Fn] Function

[``Fi] Function Instance

[`S2;A] Source Zone A

[`S;Lo] Scale Low

[`S;hi] Scale High

[`r;Lo] Range Low

[`r;hi] Range High

[`o;CA] Calibration Offset

[ALM]

[`Set] Alarm Menu

[```1]

[ALM] Alarm (1 to 8)

[`A;ty] Type

[`Sr;A] Source

[`is;A] Source Instance

[`S2;A] Source Zone

[`A;hy] Hysteresis

[`a;Lg] Logic

[`A;SD] Sides

[`A;Lo] Low Set Point **

[`A;hi] High Set Point **

[`a;LA] Latching

[`A;bL] Blocking

[`a;Si] Silencing

[A;dsp] Display

[`A;dL] Delay Time

[a;Clr] Clear Request **

[a;sir] Silence Request **

[`a;st] State **

[CUrr]

[`Set] Current Menu

[```1]

[CUrr] Current 1 to 4

[`C;Sd] Sides

[`C;Ur] Read Enable

[`C;dt] Detection Threshold

[`C;SC] Input Current Scaling

[C;ofs] Heater Current Offset

[`C;Si] Output Source Instance

[`Lnr]

[`Set] Linearization Menu

[```1]

[`Lnr] Linearization (1 to 8)

[``Fn] Function

[SFn;A] Source Function A

[`Si;A] Source Instance A

[`S2;A] Source Zone A

[Unit] Units

[`ip;1] Input Point 1

[`op;1] Output Point 1

[`ip;2] Input Point 2

[`op;2] Output Point 2

[`ip;3] Input Point 3

[`op;3] Output Point 3

[`ip;4] Input Point 4

[`op;4] Output Point 4

[`ip;5] Input Point 5

[`op;5] Output Point 5

[`ip;6] Input Point 6

[`op;6] Output Point 6

[`ip;7] Input Point 7

[`op;7] Output Point 7

[`ip;8] Input Point 8

Setup Page Parameters

To navigate to the Setup Page using the RUI, follow

the steps below:

1. From the Home Page, press both the Up ¿ and

Down ¯ keys for six seconds. [``Ai] will appear

in the upper display and [`Set] will appear in the

lower display.

Note:

If keys are released when [OPEr] is displayed, press

the Infinity Key ˆ or reset key to exit and repeat un-

til [`Set] is displayed.

2. Press the Up ¿ or Down ¯ key to view available

menus.

3. Press the Advance Key

‰

to enter the menu of

choice.

4. If a submenu exists (more than one instance), press

the Up ¿ or Down ¯ key to select and then press

the Advance Key

‰

to enter.

5. Press the Up ¿ or Down ¯ key to move through

available menu prompts.

6. Press the Infinity Key ˆ to move backwards

through the levels: parameter to submenu; submenu

to menu; menu to Home Page.

7. Press and hold the Infinity Key ˆ for two seconds to

return to the Home Page.

On the following pages, top level menus are identified

with a yellow background color.

Note:

Some of these menus and parameters may not appear, depending on the controller's options. See model number

information in the Appendix for more information. If there is only one instance of a menu, no submenus will ap-

pear.

Note:

Some of the listed parameters may not be visible. Parameter visibility is dependent upon controller part number.

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 123 124

Comentarios a estos manuales

Sin comentarios

Watlow EZ-ZONE RME Manual de usuario Pagina 42

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Watlow EZ-ZONE RME