Watlow MINICHEF 2000 Manual de usuario Pagina 51
- Pagina / 71
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Definitions of Functions, Parameters and Values
50 ■ Watlow MINIC HEF 2000 Hardware & Software Setup Guide
[der`1] Channel 1 Derivative
Sets the derivative gain for ot 1. A value of 0.00 shuts the derivative off. This parameter
appears when the selected application software set uses temperature output 1 and
[type`] is set to [``Pid] and [Pid`U] is set to [```si].
Range: 0.00 to 9.99 minutes Default: 0.00 minutes
[Cycl1] Channel 1 Cycle Time
Sets the PID cycle time for output 1. This parameter only appears when the selected
application software set uses temperature output 1 and [type`] is set to [``Pid].
Range: 1 to 60 seconds Default: 5 seconds
[ProP2] Channel 2 Proportional Band
Sets the relative proportional band for output 2. This parameter only appears when the
selected application software set uses temperature output 2 and [type`] is set to
[``Pid].
Range: 1 to 999ºF (1 to 555ºC) Default: 25ºF (14ºC)
[rset2] Channel 2 Reset
Sets the reset (integral) gain for output 2. A value of 0.00 shuts reset off. This parame-
ter only appears when the selected application software set uses a temperature output
from channel 2 and [type`] is set to [``Pid] and [Pid`U] is set to [```US].
Range: 0.00 to 9.99 repeats / minute Default: 0.00 repeats / minute
[int`2] Channel 2 Integer
Sets the integral gain for output 2. A value of 0.00 shuts the integral off. This parame-
ter only appears when the selected application software set uses a temperature output
from channel 2 and [type`] is set to [``Pid] and [Pid`U] is set to [```si]. Range:
0.00 to 99.99 minutes / repeat Default: 0.00 minutes / repeat
[rate2] Channel 2 Rate
Sets the rate (derivative) gain for output 2. A value of 0.00 shuts the rate off. This
parameter only appears when the selected application software set uses temperature
output 2 and [type`] is set to [``Pid] and [Pid`U] is set to [```US].
Range: 0.00 to 9.99 minutes Default: 0.00 minutes
[der`2] Channel 2 Derivative
Sets the derivative gain for output 2. A value of 0.00 shuts the derivative off. This
parameter appears when the selected application software set uses temperature output
2 and [type`] is set to [``Pid] and [Pid`U] is set to [```si].
Range: 0.00 to 9.99 minutes Default: 0.00 minutes
[Cycl2] Channel 2 Cycle Time
Sets the PID cycle time for output 2. This parameter only appears when the selected
application software set uses temperature output 2 and [type`
]
is set to [``Pid].
Range: 1 to 60 seconds Default: 5 seconds
Thermal Function, continued
- Hardware & Software 1
- Setup Guide 1
- All Applications 2
- Application Number Guide 3
- Introduction 4
- INICHEF 2000 ■ 5 6
- INICHEF 2000 6
- General Description 7
- Label Information: 8
- INICHEF 2000 ■ 9 10
- Step 1 Install the Controller 11
- INICHEF 2000 ■ 11 12
- Step 2 Wire the Controller 13
- S1 S2 S3 14
- Input 1 Wiring Input 2 Wiring 14
- Output 1 15
- INICHEF 2000 ■ 15 16
- Output 2 16
- Event Output 2 17
- Event Output 1 17
- MINICHEF 2000 18
- Software Structure 19
- INICHEF 2000 ■ 19 20
- -99 to 99º F (-55 to 55º C) 21
- INICHEF 2000 ■ 21 22
- On/off Temperature control 23
- Auto-tuning 23
- Configuration Procedure 24
- Step 4 Program the Menus 26
- INICHEF 2000 ■ 27 28
- To Review Menu Values 29
- INICHEF 2000 ■ 29 30
- To Set Menu Security Lock 30
- To set the time of day 31
- INICHEF 2000 ■ 31 32
- 1. Design guidelines 32
- Appendix 34
- MINICHEF 35
- 2000 Troubleshooting Chart 35
- INICHEF 2000 ■ 35 36
- Troubleshooting Chart 37
- INICHEF 2000 ■ 37 38
- INICHEF 2000 ■ 39 40
- INICHEF 2000 ■ 41 42
- INICHEF 2000 ■ 43 44
- Configuration Mode 45
- INICHEF 2000 ■ 45 46
- INICHEF 2000 ■ 47 48
- INICHEF 2000 ■ 49 50
- INICHEF 2000 ■ 51 52
- [teNp2] Channel 2 Input 53
- INICHEF 2000 ■ 53 54
- Program Mode 54
- INICHEF 2000 ■ 55 56
- Definitions of Errors 57
- INICHEF 2000 ■ 57 58
- Glossary of Terms 59
- INICHEF 2000 ■ 59 60
- INICHEF for end 60
- INICHEF 2000 default 60
- Specifications (1032) 61
- Ordering Information 62
- MINICHEF 2000 Accessories 63
- Recommended Sources of Supply 63
- MINICHEF 2000 Documentation 63
- Watlow Controls 64
- INICHEF 2000 ■ 65 66
- Declaration of Conformity 67
- INICHEF 2000 ■ 67 68
- INICHEF 2000 ■ 69 70
Relacionado con productos y manuales para Sensores Watlow MINICHEF 2000
Sensores Watlow LogicPro Manual de usuario
(296 paginas)
(296 paginas)
Sensores Watlow MLS Manual de usuario
(142 paginas)
(142 paginas)
Sensores Watlow NAFEM Gateway Manual de usuario
(51 paginas)
(51 paginas)
Sensores Watlow Power Series Rev H Manual de usuario
(72 paginas)
(72 paginas)
Sensores Watlow Power Series Manual de usuario
(72 paginas)
(72 paginas)
Sensores Watlow Power Series Manual de usuario
(72 paginas)
(72 paginas)
Sensores Watlow Power Series Manual de usuario
(28 paginas)
(28 paginas)
Sensores Watlow Power Series Manual de usuario
(28 paginas)
(28 paginas)
Sensores Watlow Power Series Manual de usuario
(72 paginas)
(72 paginas)
Sensores Watlow Power Series Manual de usuario
(28 paginas)
(28 paginas)
Sensores Watlow QPAC Manual de usuario
(34 paginas)
(34 paginas)
Sensores Watlow SBL Card Manual de usuario
(2 paginas)
(2 paginas)
Sensores Watlow SDAC Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales