Watlow MINICHEF 2000 Manual de usuario Pagina 40
- Pagina / 71
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Troubleshooting Chart
Hardware & Software Setup Guide Watlow MINICHEF 2000 ■ 39
• Determine if High or Low Deviation
Alarms are required for channel 1.
If neither are required, access the
[AL``1] parameter and set the
value to disable the deviation
alarms, choosing [`nonE] or
[`Proc]. Refer to programming
guide.
• If Deviation Alarms for channel 1
are required, confirm that the
[ALdL1] parameter is set to the
proper value for the application.
• The Offset parameter can affect the
alarm point. Confirm that the
[OFSt1] parameter is set properly.
• System may require service.
Deviation Alarm indicating a low
temperature condition for channel
1.
• Channel 1 sensor measures a low
temperature that exceeds the
allowable deviation below the pro-
grammed setpoint.
[`LO`1] appears on the
display.
System seems to be under-
heating.
• Determine if High or Low Deviation
Alarms are required for channel 2.
If neither are required, access the
[AL``2] parameter and set the
value to disable the deviation
alarms, choosing [`nonE] or
[`Proc]. Refer to programming
guide.
• If Deviation Alarms for channel 2
are required, confirm that the
[ALdH2] parameter is set to the
proper value for the application.
• The Offset parameter can affect the
alarm point. Confirm that the
[OFSt2] parameter is set properly.
• System may require service.
Deviation Alarm indicating a high
temperature condition for channel
2.
• Channel 2 sensor measures a high
temperature that exceeds the
allowable deviation above the pro-
grammed setpoint.
[`Hi`2] appears on the
display.
System seems to be over-
heating.
• Determine if High or Low Deviation
Alarms are required for channel 1.
If neither are required, access the
[AL``1] parameter and set the
value to disable the deviation
alarms, choosing [`nonE] or
[`Proc]. Refer to programming
guide.
• If Deviation Alarms for channel 1
are required, confirm that the
[ALdH1] parameter is set to the
proper value for the application.
• The Offset parameter can affect the
alarm point. Confirm that the
[OFSt1] parameter is set properly.
• System may require service.
Deviation Alarm indicating a high
temperature condition for channel
1.
• Channel 1 sensor measures a high
temperature that exceeds the
allowable deviation above the pro-
grammed setpoint.
[`Hi`1] appears on the
display.
System seems to be over-
heating.
Possible SolutionsPossible CausesSymptom/Indication
- Hardware & Software 1
- Setup Guide 1
- All Applications 2
- Application Number Guide 3
- Introduction 4
- INICHEF 2000 ■ 5 6
- INICHEF 2000 6
- General Description 7
- Label Information: 8
- INICHEF 2000 ■ 9 10
- Step 1 Install the Controller 11
- INICHEF 2000 ■ 11 12
- Step 2 Wire the Controller 13
- S1 S2 S3 14
- Input 1 Wiring Input 2 Wiring 14
- Output 1 15
- INICHEF 2000 ■ 15 16
- Output 2 16
- Event Output 2 17
- Event Output 1 17
- MINICHEF 2000 18
- Software Structure 19
- INICHEF 2000 ■ 19 20
- -99 to 99º F (-55 to 55º C) 21
- INICHEF 2000 ■ 21 22
- On/off Temperature control 23
- Auto-tuning 23
- Configuration Procedure 24
- Step 4 Program the Menus 26
- INICHEF 2000 ■ 27 28
- To Review Menu Values 29
- INICHEF 2000 ■ 29 30
- To Set Menu Security Lock 30
- To set the time of day 31
- INICHEF 2000 ■ 31 32
- 1. Design guidelines 32
- Appendix 34
- MINICHEF 35
- 2000 Troubleshooting Chart 35
- INICHEF 2000 ■ 35 36
- Troubleshooting Chart 37
- INICHEF 2000 ■ 37 38
- INICHEF 2000 ■ 39 40
- INICHEF 2000 ■ 41 42
- INICHEF 2000 ■ 43 44
- Configuration Mode 45
- INICHEF 2000 ■ 45 46
- INICHEF 2000 ■ 47 48
- INICHEF 2000 ■ 49 50
- INICHEF 2000 ■ 51 52
- [teNp2] Channel 2 Input 53
- INICHEF 2000 ■ 53 54
- Program Mode 54
- INICHEF 2000 ■ 55 56
- Definitions of Errors 57
- INICHEF 2000 ■ 57 58
- Glossary of Terms 59
- INICHEF 2000 ■ 59 60
- INICHEF for end 60
- INICHEF 2000 default 60
- Specifications (1032) 61
- Ordering Information 62
- MINICHEF 2000 Accessories 63
- Recommended Sources of Supply 63
- MINICHEF 2000 Documentation 63
- Watlow Controls 64
- INICHEF 2000 ■ 65 66
- Declaration of Conformity 67
- INICHEF 2000 ■ 67 68
- INICHEF 2000 ■ 69 70
Relacionado con productos y manuales para Sensores Watlow MINICHEF 2000
Sensores Watlow LogicPro Manual de usuario
(296 paginas)
(296 paginas)
Sensores Watlow MLS Manual de usuario
(142 paginas)
(142 paginas)
Sensores Watlow NAFEM Gateway Manual de usuario
(51 paginas)
(51 paginas)
Sensores Watlow Power Series Rev H Manual de usuario
(72 paginas)
(72 paginas)
Sensores Watlow Power Series Manual de usuario
(72 paginas)
(72 paginas)
Sensores Watlow Power Series Manual de usuario
(72 paginas)
(72 paginas)
Sensores Watlow Power Series Manual de usuario
(28 paginas)
(28 paginas)
Sensores Watlow Power Series Manual de usuario
(28 paginas)
(28 paginas)
Sensores Watlow Power Series Manual de usuario
(72 paginas)
(72 paginas)
Sensores Watlow Power Series Manual de usuario
(28 paginas)
(28 paginas)
Sensores Watlow QPAC Manual de usuario
(34 paginas)
(34 paginas)
Sensores Watlow SBL Card Manual de usuario
(2 paginas)
(2 paginas)
Sensores Watlow SDAC Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales