Watlow Series F4S/D Manual de usuario Pagina 38
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
How to Edit a Profile
To change one or more parameters in any step of a
profile, choose Edit Profile on the Profiles Page.
1. Go to the Profiles Page.
Move the cursor to Go to Profile (at the bottom
of the Main Page), then press . .
2.Choose to edit a profile.
Press . .
3.Choose the profile you want to edit.
Press . .
4.Choose how you change the profile.
Choose whether you want to insert a new step,
edit a specific step or delete a step.
To edit a step:
• Select the number of the step you wish to edit
from a list of steps and step types.
• The next screen presents a list of all possible
step types. The cursor will be positioned on
the current step type. To keep it, press . and
make your changes to the properties listed on
succeeding screens.
• If you choose to change a Step Type, the Se-
ries F4 will prompt you to program all neces-
sary parameters.
To insert a step:
Move the cursor to the number of the step that
the new step will precede. Press . . The Series
F4 will prompt you to program all necessary pa-
rameters of the new step. Inserting a step
changes the numbers of all steps that follow.
To delete a step:
Move the cursor to the number of the step to be
deleted. Press . . Deleting a step changes the
numbers of all steps that follow.
A Jump Step that jumps to an End Step cannot
be deleted.
✔
NOTE:
Inserting a step changes the numbers of all steps that
follow.
..
Edit Step:__________
>Step 1 Autostart
Step 2 Ramp Time ■
Step 3 Soak ▼
..
Choose to:__________
Insert Step
>Edit Step
Delete Step
..
…Edit Profile_______
>Glaze 42 ▲
Glaze 43 ■
Glaze 56 ▼
..
Main>Profile________
Create Profile
>Edit Profile
Delete Profile
4.6 ■ Profile Programming Watlow Series F4S/D
- User’s Manual 1
- Series F4S/D 1
- About Watlow Winona 2
- About This Manual 2
- Your Comments 2
- Technical Assistance 4
- Warranty 4
- Chapter One: Introduction 5
- 5. Run the Profile 6
- 3. Customize and Name 7
- 4. Program the Profile 7
- 2. Set up the F4 7
- Setup Steps 8
- Navigation 9
- Displays and Indicator Lights 10
- Press < to scroll 11
- > Move Up/Increase 12
- Guided Setup 13
- . to enter 14
- . to move to the 14
- < to go 14
- > and < 15
- Main Page 16
- Chapter Three: Operations 17
- Profile Control π 18
- To Resume a Profile on Hold 19
- To Hold a Running Profile 19
- Alarm Set Points 20
- Auto-tune PID 20
- Edit PID 20
- Multiple PID Sets 21
- Cascade Setup Procedure 22
- Cascade Autotuning Procedure 22
- . again 23
- Operations Page Map 26
- Autotune PID Cascade 27
- Autotune PID 27
- PID Set x (6 to 10) 28
- Autostart 34
- Ramp Time 34
- Ramp Rate 34
- Profile Plan Checklist 35
- How to Program a New Profile 36
- 6.Choose the end-state 37
- 7.Save your settings 37
- How to Edit a Profile 38
- User Profile Record 39
- Military Standard 810D 40
- Profiles Page Map 43
- Wait for: 45
- Event Output 46
- Analog Input x (1 to 3) 46
- Chapter Five: Setup 49
- Customizing the Main Page 50
- Input2 Cal. Offset 51
- Control Output x 52
- Scale Low: 0% 1-second Filter 53
- Setup Page Map 54
- Main > Setup > System 55
- Digital Input x (1 to 4) 58
- Retransmit Output x (1 and 2) 60
- Alarm Output x (1 and 2) 60
- Digital Output x (1 to 8) 61
- Communications 62
- Static Message 63
- Process Display 63
- Custom Main Page 63
- Setup Page Parameter Record 64
- Chapter Six: Features 65
- Inputs/Outputs 66
- Temperature 67
- Control Methods 68
- Dead Band 69
- Burst Fire 70
- Other Features 71
- Advanced Features 74
- Chapter Seven: Communications 77
- Series F4 Modbus Registers 78
- (expressed in percent) 79
- For more information 81
- Profile Parameters 86
- For more information about 91
- F4 Modbus Applications: 93
- (page 1 of 3) 96
- (page 2 of 3) 97
- Page Map 97
- (page 3 of 3) 98
- Jump Step End Step 99
- Renaming a Profile - F4 101
- Note: There are ten 101
- Modbus Registers for 101
- Overview 103
- Change a Password 104
- Set Lockout Menu Map 104
- Enter a Password 104
- Use a Password 104
- Set Lockout 105
- Chapter Nine: Calibration 107
- Calibrating the Series F4 108
- Process Output Procedure 110
- Retransmit Output Procedure 111
- Calibration Menu Map 112
- Calibrate Input x (1 to 3) 113
- Chapter Ten: Diagnostics 115
- Diagnostic 116
- Register 117
- Main > Factory > Test 118
- Chapter Eleven: Installation 119
- Panel Cutout 120
- Chapter Twelve: Wiring 123
- Power Wiring 124
- Thermocouple 125
- 0-20mA or 4-20mA Process 125
- 0 to 50mV 125
- Inputs x (2 and 3) 126
- Digital Inputs x (1 to 4) 128
- Outputs x (1A, 1B, 2A and 2B) 129
- Retransmit and Alarm Output 130
- Digital Outputs x (1 to 8) 131
- EIA/TIA-232 Connections 132
- EIA-232 or 133
- ICS Model 4899 133
- 59 60 61 62 134
- Appendix 135
- Glossary 136
- Series F4 139
- Specifications 140
- Ordering Information 141
- 5.10, 6.2 142
- List of Figures 147
- Series F4 Software Map 150
- Setup Page see Chapter 5 151
- Factory Page 151
- How to Reach Us 152
Relacionado con productos y manuales para Sensores Watlow Series F4S/D
Sensores Watlow Series SD Manual de usuario
(8 paginas)
(8 paginas)
Sensores Watlow Series F4S/D Manual de usuario
(102 paginas)
(102 paginas)
Sensores Watlow Series SD Limit Manual de usuario
(60 paginas)
(60 paginas)
Sensores Watlow Series PD Manual de usuario
(188 paginas)
(188 paginas)
Sensores Watlow Series V4 Manual de usuario
(21 paginas)
(21 paginas)
(80 paginas)
Sensores Watlow Silver Series EM Manual de usuario
(18 paginas)
(18 paginas)
Sensores Watlow Silver Series OIT Manual de usuario
(14 paginas)
(14 paginas)
Sensores Watlow Series V4T Manual de usuario
(26 paginas)
(26 paginas)
Sensores Watlow TLM-8 Manual de usuario
(8 paginas)
(8 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.149 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales