Watlow Series F4S/D Manual de usuario Pagina 120
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Panel Dimensions
Figure 11.2a — Multiple Panel Cutout Dimensions.
Installing the Series F4 Controller
Installing and mounting requires access to the back
of the panel.
Tools required: one #2 Phillips screwdriver.
1. Make the panel cutout using the mounting
template dimensions in this chapter.
2. Insert the controller into the panel cutout.
Check that the rubber gasket lies in its slot at
the back of the bezel. Slide the retention collar
over the case, with open holes facing the back of
the case.
Figure 11.2b — Gasket Seated on the Bezel.
3. Align the mounting bracket with the screws tips
pointed toward the panel. Squeezing the bowed
sides of the bracket, push it gently but firmly
over the case until the hooks snap into the slots
at the front of the case.
Panel Cutout
Panel
Thickness
0.375 in. maximum
(9.5 mm)
3.62 to 3.651 in.
(92 to 93 mm)
0.675 in.
(17.6 mm)
minimum
0.625 in.
(16 mm)
minimum
3.930 in.
(99.8 mm)
3.930 in.
(99.8 mm)
F
4
1
2
1B
1B
2A
2A
2B
2B
1A
1A
Main Page___________
Go to Profiles
Go to Setup
Go to Factory
i
3.62 to 3.65 in.
(92 to 93 mm)
11.2 ■ Installation Watlow Series F4S/D
- User’s Manual 1
- Series F4S/D 1
- About Watlow Winona 2
- About This Manual 2
- Your Comments 2
- Technical Assistance 4
- Warranty 4
- Chapter One: Introduction 5
- 5. Run the Profile 6
- 3. Customize and Name 7
- 4. Program the Profile 7
- 2. Set up the F4 7
- Setup Steps 8
- Navigation 9
- Displays and Indicator Lights 10
- Press < to scroll 11
- > Move Up/Increase 12
- Guided Setup 13
- . to enter 14
- . to move to the 14
- < to go 14
- > and < 15
- Main Page 16
- Chapter Three: Operations 17
- Profile Control π 18
- To Resume a Profile on Hold 19
- To Hold a Running Profile 19
- Alarm Set Points 20
- Auto-tune PID 20
- Edit PID 20
- Multiple PID Sets 21
- Cascade Setup Procedure 22
- Cascade Autotuning Procedure 22
- . again 23
- Operations Page Map 26
- Autotune PID Cascade 27
- Autotune PID 27
- PID Set x (6 to 10) 28
- Autostart 34
- Ramp Time 34
- Ramp Rate 34
- Profile Plan Checklist 35
- How to Program a New Profile 36
- 6.Choose the end-state 37
- 7.Save your settings 37
- How to Edit a Profile 38
- User Profile Record 39
- Military Standard 810D 40
- Profiles Page Map 43
- Wait for: 45
- Event Output 46
- Analog Input x (1 to 3) 46
- Chapter Five: Setup 49
- Customizing the Main Page 50
- Input2 Cal. Offset 51
- Control Output x 52
- Scale Low: 0% 1-second Filter 53
- Setup Page Map 54
- Main > Setup > System 55
- Digital Input x (1 to 4) 58
- Retransmit Output x (1 and 2) 60
- Alarm Output x (1 and 2) 60
- Digital Output x (1 to 8) 61
- Communications 62
- Static Message 63
- Process Display 63
- Custom Main Page 63
- Setup Page Parameter Record 64
- Chapter Six: Features 65
- Inputs/Outputs 66
- Temperature 67
- Control Methods 68
- Dead Band 69
- Burst Fire 70
- Other Features 71
- Advanced Features 74
- Chapter Seven: Communications 77
- Series F4 Modbus Registers 78
- (expressed in percent) 79
- For more information 81
- Profile Parameters 86
- For more information about 91
- F4 Modbus Applications: 93
- (page 1 of 3) 96
- (page 2 of 3) 97
- Page Map 97
- (page 3 of 3) 98
- Jump Step End Step 99
- Renaming a Profile - F4 101
- Note: There are ten 101
- Modbus Registers for 101
- Overview 103
- Change a Password 104
- Set Lockout Menu Map 104
- Enter a Password 104
- Use a Password 104
- Set Lockout 105
- Chapter Nine: Calibration 107
- Calibrating the Series F4 108
- Process Output Procedure 110
- Retransmit Output Procedure 111
- Calibration Menu Map 112
- Calibrate Input x (1 to 3) 113
- Chapter Ten: Diagnostics 115
- Diagnostic 116
- Register 117
- Main > Factory > Test 118
- Chapter Eleven: Installation 119
- Panel Cutout 120
- Chapter Twelve: Wiring 123
- Power Wiring 124
- Thermocouple 125
- 0-20mA or 4-20mA Process 125
- 0 to 50mV 125
- Inputs x (2 and 3) 126
- Digital Inputs x (1 to 4) 128
- Outputs x (1A, 1B, 2A and 2B) 129
- Retransmit and Alarm Output 130
- Digital Outputs x (1 to 8) 131
- EIA/TIA-232 Connections 132
- EIA-232 or 133
- ICS Model 4899 133
- 59 60 61 62 134
- Appendix 135
- Glossary 136
- Series F4 139
- Specifications 140
- Ordering Information 141
- 5.10, 6.2 142
- List of Figures 147
- Series F4 Software Map 150
- Setup Page see Chapter 5 151
- Factory Page 151
- How to Reach Us 152
Relacionado con productos y manuales para Sensores Watlow Series F4S/D
Sensores Watlow Series SD Manual de usuario
(8 paginas)
(8 paginas)
Sensores Watlow Series F4S/D Manual de usuario
(102 paginas)
(102 paginas)
Sensores Watlow Series SD Limit Manual de usuario
(60 paginas)
(60 paginas)
Sensores Watlow Series PD Manual de usuario
(188 paginas)
(188 paginas)
Sensores Watlow Series V4 Manual de usuario
(21 paginas)
(21 paginas)
(80 paginas)
Sensores Watlow Silver Series EM Manual de usuario
(18 paginas)
(18 paginas)
Sensores Watlow Silver Series OIT Manual de usuario
(14 paginas)
(14 paginas)
Sensores Watlow Series V4T Manual de usuario
(26 paginas)
(26 paginas)
Sensores Watlow TLM-8 Manual de usuario
(8 paginas)
(8 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales