Watlow Series F4P Manual de usuario Pagina 31
- Pagina / 124
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Watlow Series F4P Parameters ■ 6.5
✔ Note: For more information about how parameter set-
tings affect the controller’s operation, see the Features
Chapter.
* None of the B parameters are active if both outputs are
set to cool or heat.
Operations Page Parameter Table Modbus
Register
Range read/write Conditions for
Parameter Description (Modbus Value) Default (I/O, Set) Parameters to Appear
Active if Control Type (Analog
Input 3) is set to Cascade, PID
Units (Setup Page) is set to SI
and Proportional Band is not
set to 0.*
1A 1B Set
2601 2611 [1]
2621 2631 [2]
2641 2651 [3]
2661 2671 [4]
2681 2691 [5]
r/w
0 minutes0.00 to 99.99 minutes
(0 to 9999)
Integral x (A or B)
Set the integral time in
minutes.
[or]
Active if Control Type (Analog
Input 3) is set to Cascade.*
1A 1B Set
2600 2610 [1]
2620 2630 [2]
2640 2650 [3]
2660 2670 [4]
2680 2690 [5]
r/w
25°F
14°C
0 to 30000
0.0 to 3000.0
0.00 to 300.00
0.000 to 30.000
(0 to 30000) in integer,
tenths, hundredths or
thousandths
Proportional Band x (A or
B)
Define the proportional
band for PID control.
Main > Operations > Edit PID > Cascade Outer Loop PID Set X (1 to 5)
Cascade Outer Loop PID Set x (1 to 5)
* None of the B parameters are active if both outputs are set to cool or heat.
Active if Proportional Band is set
to 0 and one output is set to
heat and the other to cool
(Setup Page).* Based on dial
setting.
1A 1B Set
507 557 [1]
517 567 [2]
527 577 [3]
537 587 [4]
547 597 [5]
r/w
30 to 30000
0.0 to 3000.0
0.00 to 300.00
0.000 to 30.000
(0 to 30000) in integer,
tenths, hundredths or
thousandths
Hysteresis x (A or B)
Define the process vari-
able change from the set
point required to re-en-
ergize the output (in on-
off mode).
Active if Proportional Band is not
set to 0 and one output is set to
heat and the other to cool
(Setup Page).* Based on decimal
setting.
1A 1B Set
505 555 [1]
515 565 [2]
525 575 [3]
535 585 [4]
545 595 [5]
r/w
00 to 30000
0.0 to 3000.0
0.00 to 300.00
0.000 to 30.000
(0 to 30000) in integer,
tenths, hundredths or
thousandths
Dead Band x (A or B)
Define the effective shift
in the heating and cool-
ing set points to prevent
conflict.
Active if PID Units (Setup Page)
is set to U.S. and Proportional
Band is not set to 0.*
1A 1B Set
504 554 [1]
514 564 [2]
524 574 [3]
534 584 [4]
544 594 [5]
r/w
0.00 minutes0.00 to 9.99 minutes
(0 to 999)
Rate x (A or B)
Set the rate time.
Active if PID Units (Setup Page)
is set to SI and Proportional
Band is not set to 0.*
1A 1B Set
503 553 [1]
513 563 [2]
523 573 [3]
533 583 [4]
543 593 [5]
r/w
0.00 minutes0.00 to 9.99 minutes
(0 to 999)
Derivative x (A or B)
Set the derivative time.
Active if PID Units (Setup Page)
is set to U.S. and Proportional
Band is not set to 0.*
1A 1B Set
502 552 [1]
512 562 [2]
522 572 [3]
532 582 [4]
542 592 [5]
r/w
0 per minute0.00 per minute to
99.99 per minute
(0 to 9999)
Reset x (A or B)
Set the reset time in re-
peats per minute.
Active if PID Units (Setup Page)
is set to SI and Proportional
Band is not set to 0.*
1A 1B Set
501 551 [1]
511 561 [2]
521 571 [3]
531 581 [4]
541 591 [5]
r/w
0 minutes0.00 to 99.99 minutes
(0 to 9999)
Integral x (A or B)
Set the integral time in
minutes.
[or]
- User’s Manual 1
- Series F4P 1
- Safety Information 2
- Technical Assistance 2
- Your Comments 2
- Series F4P: Table of Contents 3
- Chapter One: Introduction 5
- Setup Steps 6
- How to do itWhat to do 6
- Chapter Two: Navigation and 7
- Keys, Displays and Lights 8
- Static Set Point Control 9
- Troubleshooting 10
- Alarm Set Points 15
- To Clear an Alarm or Error 15
- Edit PID 16
- Multiple PID Sets 17
- Chapter Four: Setup Page 19
- Customizing the Main Page 20
- Static Messages 20
- Chapter Five: Factory Page 21
- Enter a Password 22
- Use a Password 22
- Change a Password 22
- Diagnostics 23
- Calibration 23
- Process Output Procedure 25
- Retransmit Output Procedure 26
- Chapter Six: Parameters 27
- Main Page Parameters 28
- Register 29
- Operations Page Parameters 30
- Chapter 31
- Ramp to Set Point 33
- PID Crossover 33
- Control Set Points 34
- Remote/Local Set Points 35
- Setup Page Parameters 37
- Analog Input x (1 to 3) 38
- Analog Input 2 39
- Analog Input 3 41
- Digital Input x (1 to 4) 43
- Control Output x (1A and 1B) 44
- Alarm Output x (1 and 2) 45
- Communications 46
- Retransmit Output x (1 and 2) 46
- Custom Main Page 47
- Static Message 48
- Process Display 48
- Setup Page Parameter Record 49
- Factory Page Parameters 52
- Diagnostic 53
- Calibrate Input x (1 to 3) 55
- Chapter Seven: Features 59
- Temperature 60
- High Scale and Low Scale 62
- Digital Inputs 62
- Control Methods 63
- On-Off Control 64
- Proportional Control 64
- Dead Band 65
- Al R i h H i 69
- Advanced Features 70
- Digital Set Points 72
- Features in the 73
- Enhanced Series F4P 73
- Controller 73
- Curve A (PID) 74
- Curve B (Cascade) 74
- Curve C (Single-control) 74
- Differential Control 75
- Ratio Control 75
- Dimensions 79
- Panel Dimensions 80
- Wiring the Series F4P 83
- Thermocouple 84
- 0-20mA or 4-20mA Process 84
- 0 to 50mV 84
- Inputs x (2 and 3) 85
- Digital Inputs x (1 to 4) 87
- Outputs 1A and 1B 88
- Outputs 1A and 1B (continued) 89
- Retransmit and Alarm Output 89
- Communications Wiring 90
- ICS Model 4899 91
- EIA-232 or 91
- Wiring Example 92
- Wiring Notes 93
- Chapter Nine: Communications 95
- Series F4P Modbus Registers 96
- For more informa 99
- 606 Decimal, Analog Input 1 105
- 616 Decimal, Analog Input 2 106
- 626 Decimal, Analog Input 3 106
- Appendix 109
- Specifications 110
- Ordering Information (2330) 111
- Series F4 112
- Glossary 113
- Series F4P Software Map 121
- Setup Page see Chapter 4 122
- Factory Page see Chapter 5 122
- About Watlow Winona 123
- Warranty 123
- How to Reach Us 124
Relacionado con productos y manuales para Sensores Watlow Series F4P
Sensores Watlow Series F4P Manual de usuario
(104 paginas)
(104 paginas)
Sensores Watlow Series F4P Manual de usuario
(104 paginas)
(104 paginas)
Sensores Watlow Series F4P Manual de usuario
(104 paginas)
(104 paginas)
Sensores Watlow Series SD Manual de usuario
(8 paginas)
(8 paginas)
Sensores Watlow Series F4S/D Manual de usuario
(152 paginas)
(152 paginas)
Sensores Watlow Series SD Manual de usuario
(8 paginas)
(8 paginas)
Sensores Watlow Series F4S/D Manual de usuario
(102 paginas)
(102 paginas)
Sensores Watlow Series SD Limit Manual de usuario
(60 paginas)
(60 paginas)
Sensores Watlow Series PD Manual de usuario
(188 paginas)
(188 paginas)
Sensores Watlow Series V4 Manual de usuario
(21 paginas)
(21 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales