Watlow Series F4P Manual de usuario Pagina 12
- Pagina / 124
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2.6 ■ Operating from the Front Panel Watlow Series F4P
• Add power line filter for input power.
• Return controller to factory for repair.
• Noise on power line.
• Component failure.
• Checksum error in
Cycle device power.
• Press any key. All parameters will de-
fault.
• Module changed.• Module change. Defaults will
occur. Accept with any key.
• Replace incorrect module with re-
transmit module.
• Wrong module in retransmit 2 slot.• Retransmit 2 Module Error!
Only process modules
supported.
• Replace incorrect module with re-
transmit module.
• Wrong module in retransmit 2 slot.• Retransmit 1 Module Error!
Only process modules
supported.
• Check for correct installation of mod-
ule.
• Module not seated correctly in slot.• Verify the module.
• Check for correct installation of mod-
ule.
• Module installed incorrectly or in
wrong slot.
• Module not allowed
• Replace output module.• Output module failure.• Output 1A
• Output 1B
• Output 2A
• Output 2A
• Move module to correct input slot.
• Move module to correct input slot.
• Input module 2 or 3 is in input 1 slot.
• Input module 1 is in input 2 or 3 slot.
• Verify Input 1
• Verify Input 2 or 3
• Replace module or return controller
to factory for repair
• A module has lost its programming ID. • Incorrect ID!
• Contact factory for further informa-
tion and diagnosis.
• Component failure. • Unknown Error!
Record this number. Contact
the factory.
• Add filter to AC power line and verify
unit is power by AC voltage.
• Controller can’t detect zero cross point.
Noise is present on AC power line or
unit is not powered by AC voltage.
• Zero Cross Failure!
Switched to Fixed
Time control.
System Errors
(Upper Display shows error
numbers. Lower Display mes-
sages indicate cause and
action to take.)
• Check wiring and process valve for
compatibility.
• Process valve is wired incorrectly or in-
compatible.
Upper
Lower Slidewire time out
• Increase slidewire time out value.
• Replace process valve.
• Increase slidewire time out value.
• Check wiring and process valve for
compatibility.
• Slidewire time out value set too short.
• Slidewire valve is stuck or not
responding.
• Process valve is wired incorrectly or in-
compatible.
Upper
Lower Slidewire time out
• Return to factory for evaluation.• Component failure.
Upper
Lower !Input x Error
(x is 1 to 3)
Corrective ActionProbable Cause(s)Indication
- User’s Manual 1
- Series F4P 1
- Safety Information 2
- Technical Assistance 2
- Your Comments 2
- Series F4P: Table of Contents 3
- Chapter One: Introduction 5
- Setup Steps 6
- How to do itWhat to do 6
- Chapter Two: Navigation and 7
- Keys, Displays and Lights 8
- Static Set Point Control 9
- Troubleshooting 10
- Alarm Set Points 15
- To Clear an Alarm or Error 15
- Edit PID 16
- Multiple PID Sets 17
- Chapter Four: Setup Page 19
- Customizing the Main Page 20
- Static Messages 20
- Chapter Five: Factory Page 21
- Enter a Password 22
- Use a Password 22
- Change a Password 22
- Diagnostics 23
- Calibration 23
- Process Output Procedure 25
- Retransmit Output Procedure 26
- Chapter Six: Parameters 27
- Main Page Parameters 28
- Register 29
- Operations Page Parameters 30
- Chapter 31
- Ramp to Set Point 33
- PID Crossover 33
- Control Set Points 34
- Remote/Local Set Points 35
- Setup Page Parameters 37
- Analog Input x (1 to 3) 38
- Analog Input 2 39
- Analog Input 3 41
- Digital Input x (1 to 4) 43
- Control Output x (1A and 1B) 44
- Alarm Output x (1 and 2) 45
- Communications 46
- Retransmit Output x (1 and 2) 46
- Custom Main Page 47
- Static Message 48
- Process Display 48
- Setup Page Parameter Record 49
- Factory Page Parameters 52
- Diagnostic 53
- Calibrate Input x (1 to 3) 55
- Chapter Seven: Features 59
- Temperature 60
- High Scale and Low Scale 62
- Digital Inputs 62
- Control Methods 63
- On-Off Control 64
- Proportional Control 64
- Dead Band 65
- Al R i h H i 69
- Advanced Features 70
- Digital Set Points 72
- Features in the 73
- Enhanced Series F4P 73
- Controller 73
- Curve A (PID) 74
- Curve B (Cascade) 74
- Curve C (Single-control) 74
- Differential Control 75
- Ratio Control 75
- Dimensions 79
- Panel Dimensions 80
- Wiring the Series F4P 83
- Thermocouple 84
- 0-20mA or 4-20mA Process 84
- 0 to 50mV 84
- Inputs x (2 and 3) 85
- Digital Inputs x (1 to 4) 87
- Outputs 1A and 1B 88
- Outputs 1A and 1B (continued) 89
- Retransmit and Alarm Output 89
- Communications Wiring 90
- ICS Model 4899 91
- EIA-232 or 91
- Wiring Example 92
- Wiring Notes 93
- Chapter Nine: Communications 95
- Series F4P Modbus Registers 96
- For more informa 99
- 606 Decimal, Analog Input 1 105
- 616 Decimal, Analog Input 2 106
- 626 Decimal, Analog Input 3 106
- Appendix 109
- Specifications 110
- Ordering Information (2330) 111
- Series F4 112
- Glossary 113
- Series F4P Software Map 121
- Setup Page see Chapter 4 122
- Factory Page see Chapter 5 122
- About Watlow Winona 123
- Warranty 123
- How to Reach Us 124
Relacionado con productos y manuales para Sensores Watlow Series F4P
Sensores Watlow Series F4P Manual de usuario
(104 paginas)
(104 paginas)
Sensores Watlow Series F4P Manual de usuario
(104 paginas)
(104 paginas)
Sensores Watlow Series F4P Manual de usuario
(104 paginas)
(104 paginas)
Sensores Watlow Series SD Manual de usuario
(8 paginas)
(8 paginas)
Sensores Watlow Series F4S/D Manual de usuario
(152 paginas)
(152 paginas)
Sensores Watlow Series SD Manual de usuario
(8 paginas)
(8 paginas)
Sensores Watlow Series F4S/D Manual de usuario
(102 paginas)
(102 paginas)
Sensores Watlow Series SD Limit Manual de usuario
(60 paginas)
(60 paginas)
Sensores Watlow Series PD Manual de usuario
(188 paginas)
(188 paginas)
Sensores Watlow Series V4 Manual de usuario
(21 paginas)
(21 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales