Watlow Series SD31 PID with Optional Countdown Timer Manual de usuario Pagina 65
- Pagina / 72
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Watlow Series SD31 ■ 63 ■ Appendix
Specifications
Controller
• 1/32 DIN, microprocessor-based, user-selectable control modes
• Heat and cool autotune for control outputs
• 1 Universal input, 2 outputs
• Control outputs user-selectable as on-off, P, PI, PID
• Display update: 10 Hz, adjustable digital filter
• Output update: burst, 0.1 to 999.9 seconds
• Communication output isolated
• Displayed in °C, °F or process units
Operator Interface
• Single 4-digit LED displays
• SET, Infinity (Home), Up Arrow, Down Arrow, tactile keys
Standard Conditions For Specifications
• Ambient temperature 25°C (77°F) ±3°C, rated line voltage, 50
to 60Hz, 0 to 90% RH non-condensing, 15-minute warm-up
Universal Input
• Sampling rate: 6.5 Hz.
Thermocouple
• Type J, K, T, E, N, C (W5), D (W3), PTII (F), R, S, B thermocou-
ple types. Whole or tenth of a degree resolution.
• >20 MΩ input impedance
• Maximum 20 Ω source resistance
RTD
• 2- or 3-wire platinum, 100 Ω
• DIN curve (.00385 curve)
• Whole or tenth degree indication
• 390 µA nominal RTD excitation currrent
Process
• Range selectable: 0 to 10VÎ (dc), 0 to 5VÎ (dc), 1 to 5VÎ (dc), 0
to 20 mA, 4 to 20 mA. (Can reverse low and high values.)
• Voltage input impedance 20 kΩ
• Current input impedance 100 Ω
• Minimum current source resistance 1 MΩ
• Input resolution 50,000 bits (approximately) at full scale
Input Accuracy Span Ranges
Thermocouple Input
• Calibration accuracy: ±0.1% of input accuracy span ±1°C at
standard conditions
• Temperature stability: ±0.2 degree per degree change in
ambient for J, K, T, E, N, F
±0.3% for C and D
±0.4% for B, R (excluding 0 to 100°C) and S (excluding 0 to
100°C)
±0.5% for R and S (entire input accuracy range)
RTD Input
• Calibration accuracy ±0.1% of input accuracy span ±1°C at
standard conditions
• Temperature stability: ±0.05 degree per degree change in
ambient
Process Input
• Voltage input ranges
Accuracy ±10mV ±1 LSD at standard conditions
Temperature stability ±100 ppm/°C maximum
• Milliamp input ranges
Accuracy ±20µA ±1 LSD at standard conditions
Temperature stability ±100 ppm/°C maximum
Allowable Operating Ranges
Output Types
• Output update rate: 6.5 Hz.
Switched DC
• Supply voltage minimum: 6VÎ (dc) @ 30 mA
• Supply voltage maximum: 12VÎ (dc) into an infinite load
Solid-state Relay
• Optically isolated
• Zero cross switched
• Without contact suppression
• Minimum load current: 10 mA rms
• Maximum current: 0.5A rms at 24 to 240VÅ (ac), resistive
• 20 VA pilot duty, 120/240VÅ (ac), inductive
• Must use RC suppression for inductive loads
• Maximum offstate leakage current: 100 µA rms
Type J: 32 to 1,500°F or 0 to 816°C
Type K: -328 to 2,500°F or -200 to 1,371°C
Type T: -328 to 750°F or -200 to 399°C
Type E: -328 to 1,470°F or -200 to 799°C
Type N: 32 to 2,372°F or 0 to 1,300°C
Type C (W5): 32 to 4,200°F or 0 to 2,316°C
Type D (W3): 32 to 4,200°F or 0 to 2,316°C
Type PTII (F): 32 to 2,543°F or 0 to 1,395°C
Type R: 32 to 3,200°F or 0 to 1,760°C
Type S: 32 to 3,200°F or 0 to 1,760°C
Type B: 32 to 3,300°F or 0 to 1,816°C
RTD (DIN) -328 to 1,472°F or -200 to 800°C
Process -1,999 to 9,999 units
Appendix
A
Type J: 32 to 1,382°F or 0 to 750°C
Type K: -328 to 2,282°F or -200 to 1,250°C
Type T: -328 to 662°F or -200 to 350°C
Type E: -328 to 1,470°F or -200 to 799°C
Type N: 32 to 2,282°F or 0 to 1,250°C
Type C (W5): 32 to 4,200°F or 0 to 2,316°C
Type D (W3): 32 to 4,200°F or 0 to 2,316°C
Type PTII (F): 32 to 2,540°F or 0 to 1,393°C
Type R: 32 to 2,642°F or 0 to 1,450°C
Type S: 32 to 2,642°F or 0 to 1,450°C
Type B: 1,598 to 3,092°F or 870 to 1,700°C
RTD: -328 to 1,472°F or -200 to 800°C
Process: -1,999 to 9,999 units
- User’s Manual 1
- Series SD31 1
- Single Display PID Controller 1
- Safety Information 2
- Technical Assistance 2
- Warranty 2
- Table of Contents 3
- Overview 4
- autotune 5
- Install and Wire 6
- Removing the SD31 Controller 7
- Wiring the Series SD31 8
- Figure 7b — RTD Input (100 9
- Figure 7c — 0 to 10V 9
- Figure 7d — 0 to 50mV 9
- 0 to 20 mA Process Input 10
- Output 1 Mechanical Relay 10
- Output 1 Solid-state Relay 10
- Output 1 Switched DC 11
- Output 1 Process 11
- Output 2 Mechanical Relay 11
- Output 2 Solid-state Relay 12
- Output 2 Switched DC 12
- Output 2 EIA/TIA-485 12
- 12VÎ (dc) 13
- Ethernet Gateway 14
- Home Page Overview 17
- ;ht] Rate Heat 18
- Setup Page Overview 19
- Factory Page Overview 20
- Programming Page Overview 20
- Read/Write 21
- Offset the input reading 31
- Programming Page Example 37
- Countdown Timer 38
- • SP is used when not timing 40
- Timer Example 44
- Calibrating the Series SD31 48
- Process Output Procedures 49
- Restoring Factory Calibration 49
- Features 50
- Operations Page 51
- Autotuning 51
- IS1 IS2 IS3 IS4 52
- 123 456 789 258 52
- Filter Time Constant 53
- Sensor Selection 53
- Access Lockout 53
- High Scale and Low Scale 53
- Control Methods 54
- On-Off Control 55
- Proportional Control 55
- (PID) Control 56
- Dead Band 56
- Nonlinear output curve 57
- Independent Heat and Cool PID 57
- Variable Time Base 57
- Process or Deviation Alarms 58
- Alarm Set Points 58
- Alarm Hysteresis 59
- Alarm Latching 59
- Alarm Silencing 59
- Retransmit 59
- Communications 60
- Troubleshooting 62
- Error Messages 64
- Appendix 65
- Power Supply H or L 67
- Output 1 C, K, F or J 67
- Output 2 A, C, K, J or U 67
- Timer Option A or T 67
- Prompt Index 70
- Series SD 71
- How to Reach Us 72
Relacionado con productos y manuales para Sensores Watlow Series SD31 PID with Optional Countdown Timer
Sensores Watlow Series PD Manual de usuario
(188 paginas)
(188 paginas)
Sensores Watlow Series V4 Manual de usuario
(21 paginas)
(21 paginas)
Sensores Watlow Silver Series EM Manual de usuario
(18 paginas)
(18 paginas)
Sensores Watlow Silver Series OIT Manual de usuario
(14 paginas)
(14 paginas)
Sensores Watlow Series V4T Manual de usuario
(26 paginas)
(26 paginas)
Sensores Watlow TLM-8 Manual de usuario
(8 paginas)
(8 paginas)
Sensores Watlow WATVIEW Manual de usuario
(36 paginas)
(36 paginas)
Sensores Watlow Serie 96 Manual de usuario
(92 paginas)
(92 paginas)
Sensores Watlow Silver Series Manual de usuario
(204 paginas)
(204 paginas)
Sensores Watlow 8PID Controller Manual de usuario
(55 paginas)
(55 paginas)
Sensores Watlow 12LS Controller Manual de usuario
(111 paginas)
(111 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales