Watlow Series SD31 PID with Optional Countdown Timer Manual de usuario Pagina 25
- Pagina / 72
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Watlow Series SD31 ■ 23 ■ Chapter 5 Setup
Display Parameter Name
Description
Settings Range
(Integer values for Modbus
in parentheses.)
Default Modbus*
(less 40,001
offset)
Read/Write
Appears if:
Note: Some values will be rounded off to fit in the four-character display. Full values can be read with Modbus.
* Low numbers contain the two lower bytes; high numbers contain the two higher bytes of the four-byte integer.
Decimal precision is set in another parameter.
** Timer model only (SD31-XXXX-XTXX)
[ti;En]
[ti.En]
Timer Enable
Set to enable the countdown timer func-
tion.
[`~no]
no (0)
[~YEs]
yes (1)
[`~no]
(0)
391 R/W
Timer model only,
SD31-XXXX-XTXX.
[`Ot1]
or
[`Ot2
]is set
to
[tim]
.
[hour]
[hour]
Countdown Time Hours
Set the number of hours for the count-
down time.
0-99
hours
(0 to 99000)
0
392 R/W
Timer model only,
SD31-XXXX-XTXX.
[`Ot1]
or
[`Ot2
]is set
to
[tim]
.
[Min]
[Min]
Countdown Time Minutes
Set the number of minutes for the count-
down time.
0-59
minutes
(0 to 59000)
0
393 R/W
Timer model only,
SD31-XXXX-XTXX.
[`Ot1]
or
[`Ot2
]is set
to
[tim]
.
[`Sec]
[ SEc]
Countdown Time Seconds
Set the number of seconds for the count-
down time.
0-59
seconds
(0 to 59000)
0
394 R/W
Timer model only,
SD31-XXXX-XTXX.
[`Ot1]
or
[`Ot2
]is set
to
[tim]
.
[ti;St]
[ti.St]
Timer Start Method
Select the method used to start the timer
sequence.
[imd]
Immediate (0)
[~rdy]
Ready (1)
[rdy;A]
Ready Acknowledge
(2)
[PWr]
Power Up (3)
[imd]
(0)
399 R/W
Timer model only,
SD31-XXXX-XTXX.
[`Ot1]
or
[`Ot2
]is set
to
[tim]
.
[ti;SP]
[ti.SP]
Timer Set Point
Select what set point is used during tim-
ing.
[~Off]
Off (0)
[trac]
Track (1)
[PrE;s]
Preset (2)
[trac]
(1)
401 R/W
Timer model only,
SD31-XXXX-XTXX.
[`Ot1]
or
[`Ot2
]is set
to
[tim]
.
[`rdy]
[ rdY]
Ready Band
Set the deviation band, in degrees from
set point, that would be considered a
ready condition.
1-9999
degrees
(1000 - 9999000)
10
(10000)
*395, 396
R/W
Timer model only,
SD31-XXXX-XTXX.
[ti;St]
is set to
[~rdy]
or [
rdy;A].
[rdy;L]
[rdY.L]
Ready Light Enable
When enabled, the ready light will be lit if
the process value is within the ready
band.
[`~no]
no (0)
[~YEs]
yes (1)
[`~no]
(0)
400 R/W
Timer model only,
SD31-XXXX-XTXX.
[ti;St]
is set to
[~rdy]
or [
rdy;A].
[Ot`1]
[Ot 1]
Output 1 Function
Set Output 1 function.
[`OFF]
Off (0)
[Pr;AL]
Process Alarm (1)
[dE;;AL]
Deviation Alarm (2)
[hEAt]
Heat Control (3)
[CooL]
Cool Control (4)
[rMt]
Retransmit (6)
[tim]
Timer (7)**
[hEAt]
(3)
143 R/W
Always active.
- User’s Manual 1
- Series SD31 1
- Single Display PID Controller 1
- Safety Information 2
- Technical Assistance 2
- Warranty 2
- Table of Contents 3
- Overview 4
- autotune 5
- Install and Wire 6
- Removing the SD31 Controller 7
- Wiring the Series SD31 8
- Figure 7b — RTD Input (100 9
- Figure 7c — 0 to 10V 9
- Figure 7d — 0 to 50mV 9
- 0 to 20 mA Process Input 10
- Output 1 Mechanical Relay 10
- Output 1 Solid-state Relay 10
- Output 1 Switched DC 11
- Output 1 Process 11
- Output 2 Mechanical Relay 11
- Output 2 Solid-state Relay 12
- Output 2 Switched DC 12
- Output 2 EIA/TIA-485 12
- 12VÎ (dc) 13
- Ethernet Gateway 14
- Home Page Overview 17
- ;ht] Rate Heat 18
- Setup Page Overview 19
- Factory Page Overview 20
- Programming Page Overview 20
- Read/Write 21
- Offset the input reading 31
- Programming Page Example 37
- Countdown Timer 38
- • SP is used when not timing 40
- Timer Example 44
- Calibrating the Series SD31 48
- Process Output Procedures 49
- Restoring Factory Calibration 49
- Features 50
- Operations Page 51
- Autotuning 51
- IS1 IS2 IS3 IS4 52
- 123 456 789 258 52
- Filter Time Constant 53
- Sensor Selection 53
- Access Lockout 53
- High Scale and Low Scale 53
- Control Methods 54
- On-Off Control 55
- Proportional Control 55
- (PID) Control 56
- Dead Band 56
- Nonlinear output curve 57
- Independent Heat and Cool PID 57
- Variable Time Base 57
- Process or Deviation Alarms 58
- Alarm Set Points 58
- Alarm Hysteresis 59
- Alarm Latching 59
- Alarm Silencing 59
- Retransmit 59
- Communications 60
- Troubleshooting 62
- Error Messages 64
- Appendix 65
- Power Supply H or L 67
- Output 1 C, K, F or J 67
- Output 2 A, C, K, J or U 67
- Timer Option A or T 67
- Prompt Index 70
- Series SD 71
- How to Reach Us 72
Relacionado con productos y manuales para Sensores Watlow Series SD31 PID with Optional Countdown Timer
Sensores Watlow Series PD Manual de usuario
(188 paginas)
(188 paginas)
Sensores Watlow Series V4 Manual de usuario
(21 paginas)
(21 paginas)
Sensores Watlow Silver Series EM Manual de usuario
(18 paginas)
(18 paginas)
Sensores Watlow Silver Series OIT Manual de usuario
(14 paginas)
(14 paginas)
Sensores Watlow Series V4T Manual de usuario
(26 paginas)
(26 paginas)
Sensores Watlow TLM-8 Manual de usuario
(8 paginas)
(8 paginas)
Sensores Watlow WATVIEW Manual de usuario
(36 paginas)
(36 paginas)
Sensores Watlow Serie 96 Manual de usuario
(92 paginas)
(92 paginas)
Sensores Watlow Silver Series Manual de usuario
(204 paginas)
(204 paginas)
Sensores Watlow 8PID Controller Manual de usuario
(55 paginas)
(55 paginas)
Sensores Watlow 12LS Controller Manual de usuario
(111 paginas)
(111 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales