Watlow Series V4 Manual de usuario descargar pdf (Pagina 21)

Parameter Value Range Factory Default

[`Pb1] If [`dFL] is set to [``US]:

0 - 999°F/0 - 555°C/0 - 999 Units 25°F

0 - 99.9°F/0 - 55.5°C/0 - 99.9 Units 2.5°F

0 is set to ON/OFF control. [`HSC] is set to switch diff.

If [`dFL] is set to [``SI]:

0.0 to 999.9% of span 3%

[`rE1] 0.00 to 9.99 repeats/minute 0.00 repeats/minute

0.00 = No Reset. Won't appear if [`Pb1] is set to 0

or [`dFL] is set to [``SI].

[`It1] 0.0 - 99.9 minutes/rpt. 0.00 = No Integral. 00.0 minutes/repeat

Won't appear if [`Pb1] is set to 0 or [`dFL] is set to [``US].

[`rA1] 0.00 to 9.99 minutes 0.00 minutes

0.00 = No Rate. Will not appear if [`Pb1] is set to 0

or [`dFL] is set to [``SI].

[`dE1] 0.00 - 9.99 minutes. 0.00 = No Derivative. 0.00 minutes

Won't appear if [`Pb1] is set to 0 or [`dFL] is set to [``US].

[`Ct1] 0.1 to 999.9 5.0 seconds

Won't appear if [`Pb1] = 0, or [`420].

[`Pb2] Same as [`Pb1]. [`Pb2] lower limit = 1, 0.1, 0.01

[`rE2] Same range as [`rE1].

[`It2] Same range as [`It1].

[`rA2] Same range as [`rA1].

[`dE2] Same range as [`dE1].

[`Ct2] Same range as [`Ct1].

[`ALO]

Deviation [``dE] -999 to 0 -999

Process [``Pr] [``rL] to [`AHI] [``rL]

Will not appear if [`Ot2] is set to [``no] or [`Con].

[`AHI]

Deviation [``dE] 0 to 999 999

Process [``Pr] [`ALO] to [``rH] [``rH]

Will not appear if [`Ot2] is set to [``no] or [`Con].

[`CAL] ±180°F/±100°C/±180 Units 0

[`AUt] 0-3 0

Series V4 Software Map

Parameter Value Range Factory Default Appears If:

[`LOC] [```0], [```1], [```2], [```3], [```4]** 0

[``In] [```J], [```H], [```t], [```n], [```J] DIP switch selectable.

[```S], [`rtd], [`r†d], [`0-5], [`420]

[`dEC] 0, 0.0, 0.00 0 [``In] is set to [`0-5]

or [`420]

[`C_F] [```C] or [```F] Dependent on [`dFL] [``In] is set to [```J],

[```H], [```t], [```n],

[```S], [`rtd], or [`r†d]

[``rL] [``rL] to [``rh] Input dependent.

[``rh] [``rh] to [``rL] Input dependent.

[`Ot1] [``ht] or [``CL] [``ht]

[`HSC] 1 - 99, 0.1 - 9.9, 0.01 - 0.99°F 3, 0.3, 0.03°F

1 to 55, 0.1 to 5.5, 0.01 to 0.55°C 2, 0.2, 0.02°C

[`Ot2] [`Con] = Control [`Con]

[`PrA] = Process Alarm

[``Pr] = Process with no alarm message

[`dEA] = Deviation alarm

[``dE] = Deviation with no alarm message

[``no] = None

[`HSA] 1 - 9999, 0.1 - 999.9, 0.01 - 99.99°F 3, 0.3, 0.03°F [`Ot2] is not set to [`Con]

1 - 5555, 0.1 - 555.5, 0.01 - 55.55°C 2, 0.2, 0.02°C or [``no]

[`LAt] [`LAt] or [`nLA] [`nLA] [`Ot2] is not set to [`Con]

or [``no]

[`SIL] [``On] or [`OFF] [`OFF] [`Ot2] is set to [`dEA] or

[``dE]

[`rtd] [`JIS] or [`din] [`din] [``In] is set to [`rtd] or

[`r†d]

[`rP`] [`Str] is set to Ramping on power up [`OFF]

[``on] is set to Ramping to set point always

[`OFF] is set to None

[`rt`] 0 to 9999 100°/hr [``rP] is not set to [`OFF]

[`P`L] 0 to 100 100

[`dsP] [`nor] = normal [`nor]

[`SEt] = Set Point (lower only)

[`Pro] = Process (upper only)

Setup Menu

Operation Menu

Enter the Setup Menu by

pressing the ¿Up-arrow

and ¯Down-arrow keys si-

multaneously for three sec-

onds. The lower display

shows the [`LOC] Lock

parameter, and the upper

display shows its current

level. All keys are inactive

until you release both keys.

You can reach the Lock

parameter from anywhere.

Use the ‰Advance key to

move through the menus

and the ¿Up-arrow and

¯Down-arrow keys to select

data. You will not see all

parameters in this menu,

depending on the con-

troller's configuration and

model number.

Note:

Do not enter any values

here; make photocopies

instead.

**LOC Functions

[```0]

: All operating parameters may be viewed or changed. Manual operation is permitted. Bumpless transfer to manual

mode will occur on sensor break.

[```1]

: The set point, actual, and alarm settings are only visible parameters, set point is adjustable in this level. Manual

operation and auto-tune are permitted. Bumpless transfer to manual mode will occur on sensor break.

[```2]

: The set point, actual, and alarm settings are the only visible parameters, set point is adjustable in this level. Manual

operation is permitted. Bumpless transfer to manual mode will occur on sensor break.

[```3]

: The set point and actual are the only visible parameters, set point is adjustable in this level. Manual operation is not

permitted. Bumpless transfer is defeated and outputs are disabled on sensor break.

[```4]

: The set point and actual are the only visible parameters, set point is not adjustable in this level. Manual operation is

not permitted. Bumpless transfer is defeated and outputs are disabled on sensor break.

1 2 ... 16 17 18 19 20 21

Comentarios a estos manuales

Sin comentarios

Watlow Series V4 Manual de usuario Pagina 21

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Watlow Series V4