Watlow CAS Manual de usuario Pagina 49
- Pagina / 98
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using the CAS
CAS User’s Guide 39
Alarms
If an alarm occurs, an eight character alarm code is displayed in the
lower-right section of the display. If a Failed Sensor alarm occurs, the
controller also displays this short alarm message:
These alarm codes and messages are shown in the table below.
Acknowledging an Alarm
Press the Alarm Acknowledge key to acknowledge an alarm. If there are
other channels with alarm conditions, the Alarm display switches to the
next channel in alarm. Acknowledge all alarms to clear the global alarm.
The Alarm Acknowledge key operates differently in latched and
unlatched modes. In latched mode, an alarm can only be cleared when
the process is in a non-alarming state, and the Alarm Reset key is
pressed. In un-latched mode, the alarm clears automatically when the
Alarm Acknowledge key is pressed and the system is in a non-alarming
state.
Resetting an Alarm
Pressing the Alarm Reset key clears an alarm only if the system in a
non-alarming state. Otherwise, the key will operate the same as the
Alarm Acknowledge key.
Alarm Message Alarm Type
TC BREAK Thermocouple Break
HIGH PRC High process alarm
HIGH DEV High deviation alarm
LOW DEV Low deviation alarm
LOW PRC Low process alarm
CHANNEL PROCESS UNITS
CHANNEL NAME ALARM STATUS
01 90 °F
HTR1 HIGH PRC
Process Variable Engineering Units
Channel Number
Channel Name
Alarm Message
- User ’s Guide 1
- Warranty 2
- Contents 3
- CAS User’s Guide iii 5
- Overview 7
- System Diagram 8
- Parts List 8
- 10
- Introduction 11
- Specifications 13
- Digital Inputs 14
- Digital Outputs 14
- System Digital Outputs 14
- Miscellaneous Specifications 15
- 6 CAS User’s Guide 16
- Installation 17
- Precautions and Warnings 18
- Recommended Tools 19
- CAS Mounting Procedure 20
- TB-50 Mounting Instructions 21
- Grounding 24
- Thermocouple Wiring 24
- Input Wiring 24
- Communications Wiring 25
- Wiring: Noise Suppression 26
- General Wiring 27
- Connections Test 28
- Wiring Outputs 29
- Using the Cable Tie Wraps 30
- Alarm Output Connections 31
- Watchdog Timer 31
- TB-50 Connections 32
- Input Scaling 33
- Scaling Values 34
- Scaling and Calibration 35
- T/C Inputs 36
- Connecting Thermocouples 36
- Current Inputs 36
- Voltage Inputs 37
- Unused Inputs 37
- Serial Communications 38
- JU 1JU 1 39
- Configuring Communications 40
- Recommended Wire Gauges 41
- 32 CAS User’s Guide 42
- Using the CAS 43
- Front Panel 44
- Single Channel Display 46
- Job Display 47
- Change Setpoint 48
- Acknowledging an Alarm 49
- Resetting an Alarm 49
- 40 CAS User’s Guide 50
- How to Enter the Setup Menus 51
- How to Edit a Menu 51
- CAS Menus 52
- Setup Global Parameters Menu 53
- Save Setup to Job 54
- Job Select Inputs 54
- Job Select Input Polarity 55
- Startup Alarm Delay 55
- Keyboard Lock Status 56
- Scanner Address 56
- Communications Error Checking 56
- Communications Baud Rate 57
- Allen-Bradley Protocol 57
- AC Line Frequency 57
- Digital Output Polarity 58
- EPROM Information 58
- Setup Channel Inputs 59
- Pulse Sample Time 60
- Channel Name 60
- Input Units 61
- Input Reading Offset 61
- Linear Scaling Menus 62
- Variable 63
- InputR eading 63
- Display Format 64
- High Process Value 64
- High Reading 65
- Low Process Value 65
- Low Reading 66
- Input Filter 66
- Setup Channel Alarms 67
- Alarm Delay 69
- High Process Alarm Setpoint 69
- High Process Alarm Type 69
- Deviation Alarm Value 70
- High Deviation Alarm Type 70
- Low Deviation Alarm Type 71
- Low Process Alarm Setpoint 72
- Low Process Alarm Type 72
- Alarm Deadband 73
- Manual I/O Test 75
- Digital Output Test 76
- Keypad Test 76
- Troubleshooting 77
- Manual System Reset 78
- Returning the Unit 78
- TB-50 Test 79
- Checking an Analog Input 79
- Checking Digital I/O 79
- Digital Input Test 80
- Computer Problems 81
- Ground Loops 82
- Software Problems 82
- User-Written Software 82
- Changing the EPROM 83
- Appendix: Linear Scaling 85
- Examples 85
- Example 2 86
- Example 3 87
- 78 CAS User’s Guide 88
- Glossary 89
- 88 CAS User’s Guide 98
Relacionado con productos y manuales para Sensores Watlow CAS
Sensores Watlow Control Console Manual de usuario
(12 paginas)
(12 paginas)
Sensores Watlow CLS Manual de usuario
(180 paginas)
(180 paginas)
Sensores Watlow CLS200 Manual de usuario
(251 paginas)
(251 paginas)
Sensores Watlow DIN-A-MITE Style B Manual de usuario
(14 paginas)
(14 paginas)
Sensores Watlow DIN-A-MITE Style B Manual de usuario
(12 paginas)
(12 paginas)
Sensores Watlow DIN-A-MITE Style B Manual de usuario
(12 paginas)
(12 paginas)
Sensores Watlow CPC400 Manual de usuario
(230 paginas)
(230 paginas)
Sensores Watlow DIN-A-MITE Style B Manual de usuario
(12 paginas)
(12 paginas)
Sensores Watlow DIN-A-MITE Style C Manual de usuario
(20 paginas)
(20 paginas)
Sensores Watlow DIN-A-MITE Style C Manual de usuario
(20 paginas)
(20 paginas)
Sensores Watlow DIN-A-MITE Style C Manual de usuario
(22 paginas)
(22 paginas)
Sensores Watlow DIN-A-MITE Style C Manual de usuario
(20 paginas)
(20 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales